09166-17004 Suzuki Thrust Washer


09166-17004 Thrust Washer Suzuki DT50, DT50, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50M, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT50W, DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLG, DT55TCLH, D Thrust
09166-17004 Thrust Washer Suzuki
Rating:
43

Buy Thrust Washer 09166-17004 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Suzuki entire parts catalog list:

DT50 1980,1981,1982
DT50 1983
DT50ELB 1977
DT50ELC 1978
DT50ELN 1979
DT50ESB 1977
DT50ESC 1978
DT50ESN 1979
DT50M 1980,1981,1982
DT50MLC 1978
DT50MLN 1979
DT50MSC 1978
DT50MSN 1979
DT50W 1980,1981,1982
DT55CLF 1985
DT55CRLG 1986,1987
DT55CRLJ 1988
DT55CRLK 1989
DT55CRLL 1990
DT55CRSG 1986
DT55CRSH 1987
DT55HTCLH 1987
DT55HTCLJ 1988
DT55HTCLK 1989
DT55HTCLL 1990
DT55TCLG 1986
DT55TCLH 1987
DT55TCLJ 1988
DT55TCLK 1989
DT55TCLL 1990
DT55TCLM 1991
DT55TCLN 1992
DT55TCLP 1993
DT55TCLR 1994
DT55TCLS 1995
DT55TCLT 1996
DT55TCLV 1997
DT55TCSG 1986
DT55TCSH 1987
DT65 1980,1980,1981,1981,1982,1982
DT65 1980,1980,1981,1981,1982,1982
DT65CRLG 1986
DT65CRLH 1987
DT65CRLJ 1988
DT65CRLK 1989
DT65CRLL 1990
DT65CRSG 1986
DT65CRSH 1987
DT65ELC 1978
DT65ELN 1979
DT65ESC 1978
DT65ESN 1979
DT65HTCLK 1989
DT65HTCLL 1990
DT65TCLF 1985
DT65TCLG 1986
DT65TCLH 1987
DT65TCLJ 1988
DT65TCLK 1989
DT65TCLL 1990
DT65TCLM 1991
DT65TCLN 1992
DT65TCLP 1993
DT65TCLR 1994
DT65TCLS 1995
DT65TCLT 1996
DT65TCLV 1997
DT65TCSG 1986
DT65TCSH 1987

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
3216-11
Aftertreatment #1 Intake NOx : Other Failure Mode 3655-11
Aftertreatment #1 Intake NOx Level Sensor : Other Failure Mode The #1 intake NOx sensor heater cannot generate enough heat or the power supply is intermittent.
3216-12
Aftertreatment #1 Intake NOx : Failure 3655-12
Aftertreatment #1 Intake NOx Level Sensor : Failure A failed #1 intake NOx sensor has been detected.
3226-11
Aftertreatment #1 Outlet NOx : Other Failure Mode 3609-11
Aftertreatment #1 Outlet #1 NOx Level Sensor : Other Failure Mode The #1 outlet NOx sensor heater cannot generate enough heat or the power supply is intermittent.
3226-12
Aftertreatment #1 Outlet NOx : Failure 3609-12
Aftertreatment #1 Outlet #1 NOx Level Sensor : Failure A failed #1 outlet NOx sensor has been detected.
3360-12
Aftertreatment #1 DEF Controller : Failure 3820-12
Aftertreatment #1 Diesel Exhaust Fluid Controller : Failure The #1 Diesel Exhaust Fluid Controller (DCU) has been flashed or a failed #1 DCU has been detected.
7538-12
Aftertreatment #1 DEF Controller #2 : Failure 4797-12
Aftertreatment #1 Diesel Exhaust Fluid Controller #2 : Failure The #2 DCU has been flashed or a failed #2 DCU has been detected.
7649-11
Aftertreatment #1 SCR Intake NOx #2 : Other Failure Mode 3967-11
Aftertreatment #1 Intake #2 NOx Level Sensor : Other Failure Mode The #2 intake NOx sensor heater cannot generate enough heat or the power supply is intermittent.
7649-12
Aftertreatment #1 SCR Intake NOx #2 : Failure 3967-12
Aftertreatment #1 Intake #2 NOx Level Sensor : Failure A failed #2 intake NOx sensor has been detected.
7660-11
Aftertreatment #1 Outlet NOx #2 : Other Failure Mode 3610-11
Aftertreatment #1 Outlet #2 NOx Level Sensor : Other Failure Mode The #2 outlet NOx sensor heater cannot generate enough heat or the power supply is intermittent.
7660-12
Aftertreatment #1 Outlet NOx #2 : Failure 3610-12
Aftertreatment #1 Outlet #2 NOx Level Sensor : Failure A failed #2 outlet NOx sensor has been detected. Note: Turn the keyswitch to the OFF position before connecting or disconnecting these components.If the Cat® Electronic Technician (ET) will not communicate with the Electronic Control Module (ECM), refer to Troubleshooting, "Electronic Service Tool Does Not Communicate" before you begin this procedure. The procedure verifies that electrical power is being supplied to the ECM and to the service tool connector.The data links are used to communicate information between the engine ECM and other control modules that are a part of the application. Cat ET also communicates with the ECM via the data links.The service tool connector contains connections for electrical power and for the data links.When the keyswitch is in the OFF position, Cat ET may communicate with the ECM. However, the communications may be disrupted and the communications may require frequent reconnection. To avoid this problem, place the keyswitch in the ON position when Cat ET is being used.Cat ET may display the following error message:"The version of the ECM is not recognized and the integrity of the changed parameters and displayed data is not guaranteed."This message indicates that one of the following conditions exist:
The flash file in the ECM is newer than the version of Cat ET.
The latest version of Cat ET has not been installed.
Illustration 1 g06028428
The NOx sensors are on the Clean Emissions Module (CEM).
(1) Inlet 1 NOx sensor
(2) Inlet 2 NOx sensor
(3) Outlet 1 NOx sensor
(4) Outlet 2 NOx sensor
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -11 code is active or logged.
Proceed to Test Step 2.
Result: A3360-12, 3820-12, 4797-12, or 7538-12 code is active or logged,
Proceed to Test Step 4.
Result: A-12 code other than a 3360-12, 3820-12, 4797-12, or 7538-12 is active or logged.
Repair: Replace the failed NOx sensor. Refer to Special Instruction, REHS8151 for special handling instructions.
Proceed to Test Step 5.
2. Inspect the Electrical Connectors and the Wiring
A. Turn the keyswitch to the OFF position.
B. Thoroughly inspect the connectors. Refer to Troubleshooting, "Electrical Connectors-Inspect" for additional information.
C. Perform a 45 N (10 lb) pull test on the connector wires.
D. Check the harness for abrasions and pinch points.
Connectors and Wiring
Result: The connectors and wiring appear to be OK.
Proceed to Test Step 3.
Result: There is a problem with the connectors and/or wiring.
Repair: Repair or replace the connectors or wiring. Ensure that all the seals are properly in place and ensure that the connectors are coupled.
Note: The Diesel Exhaust Fluid Control Unit (DCU) connector is not serviceable.
If the problem is not resolved, proceed to Test Step 3.
3. Check the Voltage to the Affected Sensor
A. Disconnect the affected sensor from the wiring harness.
B. Turn the keyswitch to the ON position.
C. Measure the voltage on the wiring harness connector between the following:
- +Battery (supply) and -Battery (return)
Battery Voltage
Result: The measured voltage is equal to battery voltage.
Repair: Replace the failed NOx sensor. Refer to Special Instruction, REHS8151 for special handling instructions.
Proceed to Test Step 5.
Result: The measured voltage is not equal to battery voltage.
Repair: There is a problem with an intermittent battery supply. Check the power supply to the affected sensor.
If the problem is not resolved, proceed to Test Step 5.
4. Perform the "DEF Dosing Control Module Reset"
A. Connect Cat ET.
B. Select the "Selective Catalyst Reduction System".
C. Use Cat ET to perform the following diagnostic test:
- DEF Dosing Control Module Key Switch Line Test
Reset
Result: A 3360-12, 3820-12, 4797-12, or 7538-12 code is not active.
Return to service.
Result: A 3360-12, 3820-12, 4797-12, or 7538-12 code is active.
Repair: Replace the DCU.
Proceed to Test Step 5.
5. Perform the "Aftertreatment System Functional Test"
A. Connect Cat ET.
B. Select the "Selective Catalyst Reduction System".
C. Use Cat ET to perform the following diagnostic test:
- "Aftertreatment System Functional Test"
Test
Result: The test was successful.
Return to service.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts thrust Suzuki:

31361-95240
 
31361-95240 Thrust Washer Kit
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20MSN, DT25ESB, DT25ESC, DT25ESN, DT25MLB, DT25MLC, DT25MLN, DT25MSB, DT25MSC, DT25MSN, DT50, DT50, DT50M, DT50W, DT65, DT65
08211-30422
 
08211-30422 Thrust Washer
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT50ECLE, DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50MCLE, DT50MLC, DT50MLN, DT50MSC,
08211-30401
 
08211-30401 Thrust Washer
30ELE, 30ESE, 30MLE, DT20ELG, DT20ELH, DT20ELJ, DT20ESG, DT20ESH, DT20ESJ, DT20MLG, DT20MLH, DT20MLJ, DT20MSG, DT20MSH, DT20MSJ, DT25ELF, DT25ELG, DT25ELH, DT25ELJ, DT25ESG, DT25ESH, DT25ESJ, DT25MLD, DT25MLE, DT25MLF, DT25MLG, DT25MLH, DT25MLJ, DT25
09166-17003
 
09166-17003 Thrust Washer
DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT65ELC, DT65ELN, DT65ESC, DT65ESN
08211-17303
 
08211-17303 Thrust Washer
DT50ELB, DT50ELC, DT50ELN, DT50ESB, DT50ESC, DT50ESN, DT50MLC, DT50MLN, DT50MSC, DT50MSN, DT65ELC, DT65ELN, DT65ESC, DT65ESN
57100-95860
 
57100-95860 THRUST WASHER
DT50, DT50M, DT50W, DT65, DT65
09160-22024
 
09160-22024 THRUST WASHER (T:1.75)
DT50, DT50, DT50M, DT50W, DT65, DT65
09160-22025
 
09160-22025 THRUST WASHER (T:2)
DT50, DT50, DT50M, DT50W, DT65, DT65
Back to top