34108-95210 Suzuki Trim, sender


34108-95210 Trim, sender Suzuki DT75TCLG Trim
34108-95210 Trim, sender Suzuki
Rating:
48

Buy Trim, sender 34108-95210 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

Compatible models:

DT75TCLG   Suzuki

Suzuki entire parts catalog list:

DT75TCLG 1986

Information:

1. Remove bolts (1) that hold the elbow in position on the oil pump. Remove the lock and bolt (2) that holds the suction bell to the oil pan plate. 2. Bend the locks and remove four bolts (3). Remove oil pump (4).
The oil pump idler gear will fall off the pump.
Install Oil Pump
1. Install the idler gear on the oil pump. Put the oil pump in position on the cylinder block and install locks and bolts (1). Be sure the idler gear is engaged with the crankshaft gear before bolts (1) are tightened. 2. Install bolts (3) that hold the elbow to the pump.3. Install the lock and bolt (2) that holds the suction bell to the oil pan plate.end by:a) install oil panDisassemble Oil Pump
start by:a) remove oil pump1. Remove idler gear (2). Remove bearing from gear with tooling (B). 2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (C).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) and a press as follows: a) Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is 1.52 mm (.060 in.) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with tooling (A) and a press as follows: a) Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP in SPECIFICATIONS.4. Put clean engine oil on all the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly. 6. Install gears and shafts (6) in the oil pump body assembly.7. Install spacer (7) and the two keys in shafts (6). 8. Install two gears and scavenge pump body assembly (8).9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 43 7 N m (32 5 lb.ft.).10. Install the bearing in the idler gear with tooling (B) and a press until it is even with the outside surface of the gear.11. Install the idler gear.
The oil pump must turn freely by hand after it is assembled.
end by:a) install oil pump


Parts trim Suzuki:

36645-95500
 
36645-95500 Trim Lead, extension
DT75TCLD, DT75TCLE, DT75TCLF, DT75TCLG, DT75TCLH, DT85TCLD, DT85TCLE, DT85TCLF
34800-95521
 
34800-95521 Trim Meter Assembly
DT75TCLG, DT85TCLD, DT85TCLE, DT85TCLF
37852-95211
 
37852-95211 TRIM SWITCH PLATE
DF100, DF100, DF115, DF115, DF115TL, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF25, DF25Q, DF25Q(QR), DF25T, DF30, DF30Q, DF30Q(QR), DF30T, DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL, DF90, DF90TL, DT55CLF, DT55CRLG,
37854-95201
 
37854-95201 TRIM SWITCH PANEL
DT55CLF, DT55CRLG, DT55CRSG, DT55CRSH, DT55HTCLH, DT55TCLG, DT55TCLH, DT55TCSG, DT55TCSH, DT65CRLG, DT65CRLH, DT65CRSG, DT65CRSH, DT65TCLF, DT65TCLG, DT65TCLH, DT65TCSG, DT65TCSH, DT75TCLG, DT75TCLH
55125-94400
Trim Tab
55125-94400 Trim Tab
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT75TCLG, DT75TCLH
48600-94510-02M
48600-94510-01T
Back to top