34800-95520 Suzuki Trim Meter Assembly


34800-95520 Trim Meter Assembly Suzuki DT75TCLD, DT75TCLE, DT75TCLF Trim
34800-95520 Trim Meter Assembly Suzuki
Rating:
33

Buy Trim Meter Assembly 34800-95520 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

Compatible models:

Suzuki entire parts catalog list:

DT75TCLD 1983
DT75TCLE 1984
DT75TCLF 1985

Information:


Table 1
Diagnostic Trouble Codes for the Digital Throttles
J1939 Code Code Description Comments
29-3 Accelerator Pedal Position 2 : Voltage Above Normal The Electronic Control Module (ECM) detects the following conditions:
The ECM has been powered for 3 seconds.
Diagnostic code 168-4 is not active.
The setting for the upper diagnostic limit has been exceeded for one second.
If equipped, the warning lamp will come on. The diagnostic code will be logged.
29-4 Accelerator Pedal Position 2 : Voltage Below Normal The ECM detects the following conditions:
The ECM has been powered for 3 seconds.
Diagnostic code 168-4 is not active.
The setting for the lower diagnostic limit has been exceeded for one second.
If equipped, the warning lamp will come on. The diagnostic code will be logged.
29-8 Accelerator Pedal Position 2 : Abnormal Frequency, Pulse Width, or Period The ECM detects the following conditions:
The signal frequency from the digital throttle position sensor is equal to 0% or 100% for more than 2 seconds.
The ECM has been powered for at least 3 seconds.
Diagnostic codes 29-3 and 29-4 are not active.
The ECM sets the Throttle Position to "0%".
If equipped, the warning lamp will come on. The diagnostic code will be logged if the engine is running. The diagnostic code will not be logged if the engine is cranking.
91-3 Accelerator Pedal Position 1 : Voltage Above Normal The Electronic Control Module (ECM) detects the following conditions:
The ECM has been powered for 3 seconds.
Diagnostic code 168-4 is not active.
The setting for the upper diagnostic limit has been exceeded for one second.
If equipped, the warning lamp will come on. The diagnostic code will be logged.
91-4 Accelerator Pedal Position 1 : Voltage Below Normal The ECM detects the following conditions:
The ECM has been powered for 3 seconds.
Diagnostic code 168-4 is not active.
The setting for the lower diagnostic limit has been exceeded for one second.
If equipped, the warning lamp will come on. The diagnostic code will be logged.
91-8 Accelerator Pedal Position 1 : Abnormal Frequency, Pulse Width, or Period The ECM detects the following conditions:
The signal frequency from the digital throttle position sensor is equal to 0% or 100% for more than 2 seconds.
The ECM has been powered for at least 3 seconds.
Diagnostic codes 91-3 and 91-4 are not active.
The ECM sets the Throttle Position to "0%".
If equipped, the warning lamp will come on. The diagnostic code will be logged if the engine is running. The diagnostic code will not be logged if the engine is cranking.
Follow the troubleshooting procedure to identify the root cause of the fault. If a fault occurs with the primary throttle, the engine will use the secondary throttle until the fault is repaired.If a fault occurs with the secondary throttle, the engine will use the primary throttle until the fault is repaired.If a functional throttle is not available, the following conditions will occur:
The engine will default to the limp home speed.
If the engine speed is higher than the limp home speed, the engine will decelerate to the limp home speed.
If the engine speed is lower than the limp home speed, the engine speed will remain at the current speed.
The engine will remain at this speed while the diagnostic code remains active.
All inputs from the faulty throttle are ignored by the ECM until the fault is repaired.
All inputs from the repaired throttle will be ignored by the ECM until the keyswitch has been cycled.Digital Throttle Position SensorThe digital throttle position sensor is used to provide a digital throttle position signal to the ECM. The sensor output is a constant frequency signal with a pulse width that varies with the throttle position. This output signal is referred to as either a duty cycle or a pulse width modulated signal (PWM). This output signal is expressed as a percentage between 0 and 100 percent.The digital throttle position sensor is most likely to be attached directly to the throttle assembly. The digital throttle position sensor requires no adjustment.The duty cycle at low idle and the duty cycle at high idle can vary depending on the application. The percent of duty cycle is translated in the ECM into a throttle position of 3 to 100 percent.The digital throttle position sensors are powered by +5 VDC from the ECM. The supply voltage is from J1: to the digital throttle position sensor connector.If the application is using the ECM dedicated PTO functions, the digital throttle position sensor will be ignored while the engine is in PTO mode.The ECM is in PTO mode if the PTO ON/OFF Switch is ON. This status can be checked with the electronic service tool. Refer to Troubleshooting, "Power Take-Off - Test" for testing if the PTO is being used.Note: The identification letters for the terminals in the connectors may vary dependent on the manufacturer of the throttle pedal.During the following procedure, refer to the electrical schematic for the application.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P1/J1 and P2/J2 ECM connectors and the PWM throttle position sensors.
Refer to Troubleshooting, "Electrical Connector - Inspect".
B. Perform a 30 N (6.7 lb) pull test on each of the wires in the ECM connector and the PWM throttle position sensor connector.
C. Check the harness for corrosion, abrasion, and pinch points from the PWM throttle position sensor to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Wait at least 10 seconds for


Parts trim Suzuki:

55125-95202-02M
 
55125-95202-02M TRIM TAB
DT40, DT75TCLD, DT75TCLE, DT75TCLF, DT85TCLD, DT85TCLE, DT85TCLF
36645-95500
 
36645-95500 Trim Lead, extension
DT75TCLD, DT75TCLE, DT75TCLF, DT75TCLG, DT75TCLH, DT85TCLD, DT85TCLE, DT85TCLF
34801-95210
 
34801-95210 Trim Sender
DT55CLF, DT55CRLG, DT55CRSG, DT55CRSH, DT55HTCLH, DT55TCLG, DT55TCLH, DT55TCSG, DT55TCSH, DT65CRLG, DT65CRLH, DT65CRSG, DT65CRSH, DT65TCLF, DT65TCLG, DT65TCLH, DT65TCSG, DT65TCSH, DT75TCLD, DT75TCLE, DT75TCLF, DT75TCLH, DT85TCLD, DT85TCLE, DT85TCLF
Back to top