51117-87L00 Suzuki UNION, WATER INDICATOR


51117-87L00 UNION, WATER INDICATOR Suzuki DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90A, DF90A, DF90A UNION
51117-87L00 UNION, WATER INDICATOR Suzuki
Rating:
23

Buy UNION, WATER INDICATOR 51117-87L00 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Compatible models:

DF70A   DF80A   DF90A   Suzuki

Suzuki entire parts catalog list:

DF70A 2009
DF70A 2010
DF70A 2011
DF80A 2009
DF80A 2010
DF80A 2011
DF90A 2009
DF90A 2010
DF90A 2011

Information:


Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Bend the lock tab and remove bolt (1).
The oil pump idler gear (3) can fall off the pump when the pump is removed. Injury can be the result. To prevent injury, always hold idler gear on the pump when the pump is removed.
2. Bend the two tabs on locks (4) on the left hand side of the engine. Remove the four bolts (2) and (5) and remove the oil pump and suction bell as a unit. Be sure the idler gear (3) is engaged with the crankshaft gear and tabs on locks (4) on bolts (5) are not next to the oil pan gasket surface when bolts (2) and (5) are tightened. Install in reverse order.End By:a. install oil panDisassemble Oil Pump
Start By:a. remove oil pump
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Remove idler gear (2). Remove the bearing from the idler gear with tooling (B).2. Remove suction bell (1) and the bolt and the washer from the oil pump drive gear. 3. Remove the drive gear from the shaft with tooling (A).4. Remove the key from the pump shaft and bolts (3). 5. Remove body (8), two gears (7), the keys and spacer (4).6. Remove two shafts (5) and the gears.7. Remove bolts (6), the cover and the pressure relief valve. 8. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (B).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (B) and a press as follows:a. Put bearings (9) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is 1.52 mm (.060 in) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with tooling (B) and a press as follows.a. Put bearings (10) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See the topic, Oil Pump, in the Specifications module.4. Put clean engine oil on all the parts of the oil pump. 5. Install pressure relief valve (11) cover (12) and bolt (5). 6. Install shaft assemblies (13) spacer (4) and the key in the shaft assembly.7. Install the two gears on the shaft assemblies. 8. Install scavenge pump body assembly (14) and the bolts.9. Install key (15), drive gear (16), the washer and bolt (17). Tighten the bolt to a torque of 43 7 N m (32 5 lb ft).10. Install the bearing in the idler gear with tooling (B) and a press until it is even with the outside surface of the gear.11. Install the suction bell and the idler gear on the oil pump.
The oil pump must turn freely by hand after it is assembled.
End By:a. install oil pump


Parts union Suzuki:

55127-87D00
 
55127-87D00 UNION, SPEEDOMETER HOSE
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T,
09363-08004
 
09363-08004 UNION, FUEL
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T,
15773-90J00
 
15773-90J00 UNION, FUEL HOSE
DF100, DF100, DF100, DF115, DF115, DF115, DF115TL, DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, D
15830-93J00
 
15830-93J00 UNION, 3 WAY
DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250A, DF250T, DF250Z, DF300, DF300, DF300A, DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90A, DF90A, DF90A
51115-87L00
 
51115-87L00 UNION, WATER RETURN
DF70A, DF70A, DF70A, DF80A, DF80A, DF80A, DF90A, DF90A, DF90A
Back to top