13150-93310 Suzuki Valve Assembly, reed


13150-93310 Valve Assembly, reed Suzuki 20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20MSN, DT25ESB, DT25ESC, DT25ESN, DT25MLB, DT25MLC, DT25MLN, DT25MSB, DT25MSC, DT25MSN, DT28F Valve
13150-93310 Valve Assembly, reed Suzuki
Rating:
18

Buy Valve Assembly, reed 13150-93310 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 1-1
 

Suzuki entire parts catalog list:

20ELB 1977
20ELC 1978
20ELN 1979
25ELB 1977
25ELC 1978
25ELN 1979
DT20ESB 1977
DT20ESC 1978
DT20ESN 1979
DT20MLB 1977
DT20MLC 1978
DT20MLN 1979
DT20MSB 1977
DT20MSC 1978
DT20MSN 1979
DT25ESB 1977
DT25ESC 1978
DT25ESN 1979
DT25MLB 1977
DT25MLC 1978
DT25MLN 1979
DT25MSB 1977
DT25MSC 1978
DT25MSN 1979
DT28F 1979

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
416-0288 Head 1
416-0292 Adapter 1 Start By:
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove" for the correct procedure.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install suitable plugs to the inlet ports of the cylinder head in order to prevent the entry of loose parts into the engine.
Plug the apertures for the push rods in the cylinder head in order to prevent the entry of loose parts into the engine.
Note: The following procedure should be adopted to remove the valve springs when the cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head that has been removed from the engine.Note: Ensure that the appropriate piston is at the top center position before the valve spring is removed. Failure to ensure that the piston is at the top center position may allow the valve to drop into the cylinder bore.
Illustration 1 g03341307
Follow Step 1a through Step 1d to position the appropriate piston at top center.
Install Tooling (A) in position on the cylinder head to compress a valve spring for the appropriate piston.
Use Tooling (A) to compress valve spring (3) and open the valve slightly.Note: Do not compress the spring so that the valve spring retainer (2) touches the valve stem seal.
Carefully rotate the crankshaft until the piston touches the valve.Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent valve stems.
Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the piston is at the top center position. The valve is now held in a position that allows the valve spring to be safely removed.
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Note: The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that all the valve springs are installed before changing from one pair of cylinders to another pair of cylinders.
Apply sufficient pressure to Tooling (A) to allow removal of the valve keepers (1).Note: Do not compress the spring so that the valve spring retainer (2) touches the valve stem seal.
Remove valve keepers (1).
Slowly release the pressure on Tooling (A).
Remove valve spring retainer (2) and remove valve spring (3).
Remove Tooling (A).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
416-0288 Head 1
416-0292 Adapter 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft while the valve springs are removed.
Plug the apertures for the push rods in the cylinder head in order to prevent the entry of loose parts into the engine.
Install suitable plugs to the inlet ports of the cylinder head in order to prevent the entry of loose parts into the engine.


Parts valve Suzuki:

13370-28110
Valve assembly, needle
13370-28110 Valve assembly, needle
20ELB, 20ELC, 20ELN, 25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DT115, DT140, DT20ELG, DT20ELH, DT20ELJ, DT20ESB, DT20ESC, DT20ESG, DT20ESH, DT20ESJ, DT20ESN, DT20MLB, DT20MLC, DT20MLG, DT20MLH, DT20MLJ, DT20MLN, DT20MSB, DT20MSC, DT20MSG, DT20MSH, DT20MSJ,
15180-93810
 
15180-93810 Valve Set
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20MSN, DT25ESB, DT25ESC, DT25ESN, DT25MLB, DT25MLC, DT25MLN, DT25MSB, DT25MSC, DT25MSN, DT28F
13150-93311
 
13150-93311 Valve Assembly, reed
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20MSN, DT25ELZ, DT25ESB, DT25ESC, DT25ESN, DT25EST, DT25ESX, DT25ESZ, DT25MLB, DT25MLC, DT25MLN, DT25MLT, DT25MLX, DT25M
13153-93310
 
13153-93310 Valve, reed
20ELB, 20ELC, 20ELN, 25ELB, 25ELC, 25ELN, 25ELT, 25ELX, DT20ESB, DT20ESC, DT20ESN, DT20MLB, DT20MLC, DT20MLN, DT20MSB, DT20MSC, DT20MSN, DT25ELZ, DT25ESB, DT25ESC, DT25ESN, DT25EST, DT25ESX, DT25ESZ, DT25MLB, DT25MLC, DT25MLN, DT25MLT, DT25MLX, DT25M
Back to top