16710-94420 Suzuki OIL CHECK VALVE

Illustration 1 g00830348
Instrument panel
(1) Gauge cluster module
(2) Gauge cluster module
(3) Gauge cluster module
(4) Main display module
(5) Annunciator panelGauge Cluster Modules
The gauge needles are controlled by information that is processed by the main display module. For more information on the gauges, see this Operation and Maintenance Manual, "Gauges and Indicators" topic (Operation Section).
Illustration 2 g00830363
Gauge cluster module (1) displays the following parameters:
(A) Engine oil pressure
(B) Jacket water coolant temperature
(C) System voltage
(D) Fuel pressure
Illustration 3 g00830354
Gauge cluster module (2) displays the following parameters:
(E) Exhaust temperature (right side and left side)
(F) Inlet air restriction (right side and left side)
(G) Fuel filter differential pressure (restriction)
(H) Oil filter differential pressure (restriction)
Illustration 4 g00830351
Gauge cluster module (3) displays the following parameters:
(I) Inlet manifold air pressure (boost pressure)
(J) Aftercooler coolant temperature
(K) Inlet manifold air temperature
(L) Engine oil temperatureAnnunciator Panel
Illustration 5 g00830371
(1) "SCROLL" switch
(2) "CLEAR/MODE" switch
(3) "LH/RH" switch
(4) Action alarm (4)
( 5) "ALARM SILENCE" switch
(6) Potentiometer"SCROLL" switch (1) - The main display module can operate of five different modes of operation. The "SCROLL" switch is used to display the various parameters that are within each mode. See the "Main Display Module" topic."CLEAR/MODE" switch (2) - This switch is used for selecting among the main display module's five modes of operation. This switch is also used for clearing information from the main display module."LH/RH" switch (3) - This switch can be toggled to display the following parameters for the left side or the right side of the engine: exhaust temperature and inlet air restriction.Action alarm (4) - An alarm condition will not shut down the engine. However, an alarm may precede a shutdown. An alarm indicates a serious condition that requires immediate attention. Annunciation of the alarm informs the operator of an abnormal operating condition or a problem with the monitoring system. The alarm is activated by the main display module when the following conditions occur:
A diagnostic code is active.
An LED indicator on the main display module flashes.
The monitoring system detects an active event. Events can include an alarm, a derating, and shutdown."ALARM SILENCE" switch (5) - This switch enables the operator to silence the alarm for 5 minutes. If the condition that initiated the alarm is not corrected within the 5 minutes, the alarm will sound again.Potentiometer (6) - The potentiometer enables the operator to control the brightness of the lighting for the instrument panel.Main Display Module
The main display module is the brain of the system. This module receives information from the following sources:
Electronic Control Module (ECM)
Sensors
SwitchesThe display on this module includes LED indicators and a liquid crystal display.Indicators
The indicators illuminate in response to information that is received from the ECM via the CAT Data Link.Note: The indicators will illuminate if a setpoint that is programmed into the monitoring system for a parameter is reached. For information on the setpoints, refer to Troubleshooting, RENR5008, "3500B and 3500C Locomotive Engines".
Illustration 6 g00830366
Indicators for the main control module
(1) Active diagnostic code and engine shutdown
(2) Low system voltage
(3) Engine overspeed
(4) High fuel filter differential pressure (restriction)
(5) Low fuel pressure
(6) Low oil pressure
(7) High jacket water coolant temperature
(8) Low jacket water coolant temperature
(9) High aftercooler coolant temperature
(10) High inlet manifold air temperature
Active Diagnostic Code and Engine Shutdown (1) - This RED indicator illuminates when any of the following conditions occur:
An engine shutdown is initiated by the ECM.
A diagnostic code is active.
An event code is active.
Low System Voltage (2) - This RED indicator illuminates if the system voltage (battery and alternator) t