48530-97E00 VALVE, MAIN CHECK Suzuki
DT40C
VALVE
Price: query
Rating:
Compatible models:
DT40C
Suzuki
Suzuki entire parts catalog list:
- POWER TRIM & TILT (DT40TC-MODEL:94~98) » 48530-97E00
Information:
1. Fasten a hoist to the fan drive.2. Remove grease line (1) from the fan drive bracket. 3. Remove the bolts and fan drive (2) from automatic timing advance cover (3). The weight of fan drive (2) is 34 kg (75 lb.). The following steps are for the installation of the fan drive.4. Fasten a hoist and put fan drive (2) in position on the automatic timing advance cover. Install the bolts to hold the unit in position.5. Install grease line (1) on the fan drive bracket.6. Fill the fan drive with clean grease after the fan belt tightener is installed.End By:a. install fan belt tightenerb. install fanDisassemble And Assemble Fan Drive (Driven - Early D9L)
Start By:a. remove fan drive
(Early D9L)1. Remove O-ring seal (3) from hub (4).2. Remove bolt (2) and washer (1) from the end of the shaft.3. Remove hub (4) and pulley (5) from the bracket assembly. 4. Remove bolts (6) that hold pulley (5) to hub (4). 5. Use tooling (A) to remove pulley (5) from the hub. 6. Remove spacer (7) from the bracket assembly shaft or from seal (8).7. Remove bearing (11) and spacer (10) from the end of hub (4).8. Remove seal (8), then bearing (9) from the other end of hub (4). 9. If necessary, use a press and push shaft (12) out of bracket (13) in the direction shown. Shaft (12) has a shoulder on it and can only be removed from the back of bracket (13). 10. Use a hammer and punch to remove the pin that holds belt tightener shaft (14) in bracket (13). 11. Use a press and push shaft (14) out of bracket (13) as shown. The following steps are for the assembly of the fan drive.12. Put the dowel hole in shaft (14) in alignment with the dowel hole in fan drive bracket (13). Use a press and install shaft (14) in bracket (13).2. Install the pin to hold shaft (14) in bracket (13). 3. Use a press and push shaft (12) in bracket (13) from the back until the shoulder on shaft (12) is against the bracket.4. Install bearing (9) in hub (4). 5. Install dust seal (8) in hub (4) over bearing (9). Make sure the lip of the seal is toward the outside as shown.6. Put pulley (5) in position on hub (4) and install the bolts to hold the unit together.7. Put clean grease on the lip of the seal in the hub. Install spacer (7) on the fan drive bracket with the chamfer toward pulley (5).8. Install pulley (5) and the hub on the fan drive bracket.9. Install spacer (10) over the shaft in hub (4).10. Install bearing (11) over the shaft in hub (4).11. Install the O-ring seal on hub (4) and put clean grease on the seal.12. Put 9S3263 Thread Lock on the threads of the bolt. Install bolt (2) and washer (1) to hold the fan drive together. Tighten the bolt to a torque of 212 12 N m (155 10 lb.ft.).End By:a. install fan drive
Start By:a. remove fan drive
(Early D9L)1. Remove O-ring seal (3) from hub (4).2. Remove bolt (2) and washer (1) from the end of the shaft.3. Remove hub (4) and pulley (5) from the bracket assembly. 4. Remove bolts (6) that hold pulley (5) to hub (4). 5. Use tooling (A) to remove pulley (5) from the hub. 6. Remove spacer (7) from the bracket assembly shaft or from seal (8).7. Remove bearing (11) and spacer (10) from the end of hub (4).8. Remove seal (8), then bearing (9) from the other end of hub (4). 9. If necessary, use a press and push shaft (12) out of bracket (13) in the direction shown. Shaft (12) has a shoulder on it and can only be removed from the back of bracket (13). 10. Use a hammer and punch to remove the pin that holds belt tightener shaft (14) in bracket (13). 11. Use a press and push shaft (14) out of bracket (13) as shown. The following steps are for the assembly of the fan drive.12. Put the dowel hole in shaft (14) in alignment with the dowel hole in fan drive bracket (13). Use a press and install shaft (14) in bracket (13).2. Install the pin to hold shaft (14) in bracket (13). 3. Use a press and push shaft (12) in bracket (13) from the back until the shoulder on shaft (12) is against the bracket.4. Install bearing (9) in hub (4). 5. Install dust seal (8) in hub (4) over bearing (9). Make sure the lip of the seal is toward the outside as shown.6. Put pulley (5) in position on hub (4) and install the bolts to hold the unit together.7. Put clean grease on the lip of the seal in the hub. Install spacer (7) on the fan drive bracket with the chamfer toward pulley (5).8. Install pulley (5) and the hub on the fan drive bracket.9. Install spacer (10) over the shaft in hub (4).10. Install bearing (11) over the shaft in hub (4).11. Install the O-ring seal on hub (4) and put clean grease on the seal.12. Put 9S3263 Thread Lock on the threads of the bolt. Install bolt (2) and washer (1) to hold the fan drive together. Tighten the bolt to a torque of 212 12 N m (155 10 lb.ft.).End By:a. install fan drive
Parts valve Suzuki:
13370-28110
13370-28110 Valve assembly, needle
20ELB, 20ELC, 20ELN, 25ELT, 25ELX, 30ELE, 30ESE, 30MLE, DT115, DT140, DT20ELG, DT20ELH, DT20ELJ, DT20ESB, DT20ESC, DT20ESG, DT20ESH, DT20ESJ, DT20ESN, DT20MLB, DT20MLC, DT20MLG, DT20MLH, DT20MLJ, DT20MLN, DT20MSB, DT20MSC, DT20MSG, DT20MSH, DT20MSJ,
13370-97E20
13153-94400
13153-94400 VALVE, REED
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT40C
48870-97E00
48820-97E00
48830-97E00
48550-97E00
48550-94600
48550-94600 VALVE, MANUAL
DT115, DT140, DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT40C, DT55CRLJ, DT55CRLK, DT55CRLL, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLJ, DT55TC