09160-10089 Suzuki Washer

Table 1
Service Tools
Part Number Description
393-0673 EMISSIONS ANALYZER TOOL GP
349-4200 Thermometer
N/A 4 mm Allen Wrench
1U-5805 Wire Removal Tool (14-GA, GREEN)
6V-2197 Magnetic Transducer As (TIMING CALIBRATION)
121-9588 Wire Removal Tool (16-GA, BLUE)
147-6456 Wedge Removal Tool
151-6320 Wire Removal Tool (14-GA TO 18-GA, RED)
1U-5804 Crimp Tool (12−AWG TO 18−AWG)
6V-2197 Transducer
7X-1171 Transducer Adapter
7X-1695 Cable As
146-4080 Digital Multimeter Gp (RS232)
7X-1710 Multimeter Probes
326-4904 Adapter Cable As (3-PIN BREAKOUT)
208-0059 Adapter Cable As (70-PIN BREAKOUT)
(For ADEM 3 ECM (two 70-pin connectors) and for ADEM 4 ECM (one 70-pin connector and one 120-pin connector))
257-8718 The 257-8718 Adapter Cable As is not applicable with Tier IV Engines.
Adapter Cable As (120-PIN BREAKOUT)
(For ADEM 4 ECM (one 70-pin connector and one 120-pin connector))
N/A Torque Wrench (capable of applying 1.5 N m (13.3 lb in))
Repair Kits for Connectors
362-3555 Connector Repair Kit (AMPSEAL)
175-3700 Connector Repair Kit (Deutsch connector)
Bypass Harnesses for the ECM
217-0113 Wiring Harness (ECM BYPASS)
(The bypass harness connects to the battery. The bypass harness is used with the following harnesses for different types of electronic control modules.)
328-2292 Harness (ENGINE ECM BYPASS)
(For ADEM 3 ECM and ADEM 4 ECM)
277-4734 Harness (ENGINE ECM BYPASS)
(For A4:E2 ECM (Two 64-pin connectors))
276-7273 Sensor Test Box (1)
(1) Instrument used to test Cylinder Position sensors.Two short jumper wires may be needed to check the continuity of some wiring harness circuits by shorting two adjacent terminals together in a connector. A long extension wire may also be needed to check the continuity of some wiring harness circuits.Except for harness tests, the use of certain test equipment is not recommended for use on modern Caterpillar electrical circuits. Such testers include the following examples: the 8T-0500 Continuity Tester and 5P-7277 Voltage Tester.Note: A procedure has been developed to test "In Cylinder" Position Sensors. Reference Special Instruction REHS7338, "Procedure to Test the Position Sensor of a Hydraulic Cylinder".Optional Service Tools
Table 2 lists the optional service tools that may be needed during testing or repair.
Table 2
Optional Service Tools
Part Number Description
198-4240
or
1U-5470 Digital Pressure Indicator
or
Engine Pressure Group
4C-4075 Crimp Tool (4−AWG TO 10−AWG)
4C-4911(1) Battery Load Tester
5P-7277 Voltage Tester
6V-9130(2) Temperature Adapter (MULTIMETER)
8T-5319 Connector Tool Group
349-4199 AC/DC Current Probe
348-5430 Multi-Tool Gp
8T-8726 Adapter Cable As
163-5443 Adapter Cable As (3-PIN BREAKOUT)
177-2330 Battery Analyzer (DIGITAL)
190-8900 Connector Repair Kit
225-5985 Parallel Port Cable (COMMUNICATION ADAPTER)
391-8170 EMISSIONS ANALYZER TOOL GP (Bluetooth Module)
(1) Refer to Special Instructions, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8, and 12 v Lead Acid Batteries" and Special Instructions, SEHS7633, "Battery Test Procedure".
(2) Refer to Special Instructions, SEHS8382, "Use of the 6V-9130 Temperature Adapter Group".Cat® Electronic Technician (Cat ET) Service Tool
Cat ET can be used by the technician to help perform the following procedures:
Diagnostic testing
Calibrations
Flash programming
Configuration of the ECM
Print various reportsCat ET can display the following information:
Status parameters
Event codes
Diagnostic codes
ECM settings
Engine configurationAlways use the latest revision of Cat ET. The media is available on CD and the media can also be downloaded from various Caterpillar web sites.
Table 3
Software, JEBD3003, "CATERPILLAR ELECTRONIC TECHNICIAN" Once you have downloaded Cat ET onto your PC, you will need a license from your Caterpillar dealer to use the software. Various licenses are available for different users with different requirements. Consult your Caterpillar dealer.Note: For more information regarding the use of Cat ET and PC requirements, refer to the documentation that accompanies your Cat ET program software.Connecting Cat ET
Connecting the Communication Adapter
Note: The 538-5051 is the latest version of the Communication Adapter Group. Older service tool versions can still be used.Table 4 lists the standard hardware that is required to connect Cat ET.
Table 4
Standard Hardware for Connecting with Cat ET
Part Number