09160-14039 Suzuki WASHER


09160-14039 WASHER Suzuki DT150, DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, DT150STCLT, DT150TCLH, DT150TCLJ, DT150TCLK, DT150TCLL, DT150TCLM, DT150TCLN, DT150TCLP, DT150TCLR, DT150TCXGM, DT150TCXGN, DT150TCXGP, DT150TCXGR, WASHER
09160-14039 WASHER Suzuki
Rating:
18

Buy WASHER 09160-14039 Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Suzuki entire parts catalog list:

DT150 1998,1999,2000,2001,2002,2003
DT150SSH 1987
DT150SSJ 1988
DT150SSK 1989
DT150SSL 1990
DT150SSM 1991
DT150SSN 1992
DT150STCLP 1993
DT150STCLR 1994
DT150STCLS 1995
DT150STCLT 1996
DT150TCLH 1987
DT150TCLJ 1988
DT150TCLK 1989
DT150TCLL 1990
DT150TCLM 1991
DT150TCLN 1992
DT150TCLP 1993
DT150TCLR 1994
DT150TCXGM 1991
DT150TCXGN 1992
DT150TCXGP 1993
DT150TCXGR 1994
DT150TCXGS 1995
DT150TCXGT 1996
DT150TCXH 1987
DT150TCXJ 1988
DT150TCXK 1989
DT150TCXL 1990
DT150TCXM 1991
DT150TCXN 1992
DT150TCXP 1993
DT150TCXR 1994
DT150TCXS 1995
DT150TCXT 1996
DT200 1998,1999,2000,2001,2002,2003
DT225 1998,1999,2000,2001,2002,2003

Information:

If it is desired to only remove the governor so the fuel injection pump housing can be disassembled, do only Steps 2, 3, 4, 17, 24, 27, 28, 29, 30, 34, 36, 37 and 40.2. Put the fuel injection pump housing and governor in position on tool (A).3. Remove the bolts, fuel ratio control (1) and the shutoff solenoid (if equipped) from rear governor housing (2).4. Remove the bolts, rear governor housing (2) and the gasket from the front governor housing. 5. Remove governor spring (3), the two wave washers, one flat washer and the seat from the guide in the rear governor housing. 6. Remove bolt (6) that holds lever assembly (4) to the shaft assembly.7. Remove the bolts, cover assembly (5), the gasket, the shaft assembly, lever (4) and lever (7) from the rear governor housing. There is a key in the (slot) groove of the shaft assembly that must be removed before the shaft assembly is removed from the rear governor housing. 8. Remove spring (8), shaft assembly (10) and if necessary dowels (9) from the cover assembly. 9. Remove the rings, pins (13), stop (12) and plates (11) from the shaft assembly. 10. Remove pin (15) and spring (14) from the lever assembly. 11. Remove seal (16) and low idle adjustment (17) from the cover assembly. 12. Remove seal (19) from the cover assembly.13. Remove plug (18) from the cover assembly. Spacers (21) and (23) are different sizes. Make sure they are assembled in the correct position.14. Use needle nose pliers (20) and remove the shaft. Remove spacer (23), lever (22) and spacer (21) from the rear governor housing.15. If necessary remove the screws, cover (24) and the gasket from the rear governor housing. 16. If necessary, remove dashpot valve (26), fitting (27), insulator (28), high idle adjustment (29) and seal (25) from the rear governor housing. 17. Remove the bolts, front governor housing (30) and the gasket from the fuel pump housing. 18. Remove the bolts and torque control group (32) from block (33).
Depending on the different engine applications, torque control groups will vary. Inspect all parts for wear and damage and make a note of the correct sequence of the parts for assembly purposes.
19. Remove the bolts and block (33) for the full load stop from the front governor housing.20. If necessary, remove dowels (31) from the front governor housing and the dowels that align block (33). 21. Remove the bolt that holds collar (35) to bolt (36).22. Remove collar (35) and spring (34) from bolt (36). Remove bolt (36) from the block.23. If necessary, remove the stop screw from collar (35). 24. Remove the bolts and governor servo (37) from the fuel injection pump housing. 25. Remove lockring (42), seat (41), spring (broken link spring (40) and sleeve (39) from valve (38). Remove the other lockring (42) from the groove in the center of valve (38). 26. Remove valve (38), sleeve (43) and piston (45) from the governor servo. Remove the O-ring seal from sleeve (43). Remove pin (44) and lever (46). 27. Use tool (C) to hold spring (47) in compression so the ring on the governor shaft can be removed.28. Remove the ring and carefully remove tool (C).29. Remove bearing (48), the sleeves and spring (47) from the governor shaft. 30. Remove ring (50) and dashpot assembly (49) from the governor shaft. 31. Use tool (B) and remove ring (56) from seat (53).32. Remove ring (55) and spool (54) from seat (53).33. Remove seat (53), spring (52) from shield (51). 34. Remove spring (58) and riser (57) from the governor shaft. 35. Remove ring (59), races (60) and bearing (61) from the riser. 36. Remove shield (62) from the carrier assembly. Make a replacement of shield (62) any time it is removed. 37. Remove the bolts and carrier assembly (63) from the fuel pump housing. 38. Remove dowels (64) and flyweights (66) from the carrier assembly.39. Remove dowel (65) from the governor shaft and remove governor shaft from the carrier assembly. 40. Remove races (67) and (69) and bearing (68) from the camshaft in the fuel injection pump housing.Assemble Governor
1. Put the fuel injection pump housing in position on tool (A). Install race (69), bearing (68) and race (67) on the end of the camshaft in the fuel injection pump housing. 2. Put flyweights (66) in position on carrier assembly (63) and install dowels (64) to hold the flyweights in place. The flyweights must move freely on the dowels and have 0.01 to 0.23 mm (.0004 to .0090 in.) end play.3. Install governor shaft (70) on carrier assembly (63).4. Install dowel (65) in governor shaft (70) and slide carrier assembly (63) down on the governor shaft until dowel (65) fits into the slot in the carrier assembly. 5. Install carrier assembly (63) on the end of the camshaft. Make a replacement of shield (62) any time it is removed.6. Use tool (B) and install shield (62) on the carrier assembly until it is against its seat. Use a hammer and punch to move the metal (stake) two places on the side of the shield 180 5 degrees apart next to the holes in the shield. 7. Install races (60), bearing (61), and ring (59) on riser (57). 8. Install riser (57) and spring (58) on the governor shaft. 9. Install spool (54) and ring (55) on seat (53) and use tool (C) to install ring (56) to hold them in place.10. Install seat (53) on spring (52) and spring (52) on shield (51). 11. Install dash pot assembly (49) on the governor shaft as shown. 12. Install the ring in the lower groove in the governor shaft. Install sleeves, spring (47), and bearing (48) on the governor shaft.13. Use tool (D) to hold spring (47) in compression and install the ring in the groove in the governor shaft. 14. Put lever (46) in position on governor servo (37) and install pin (44) to hold the lever in


Parts washer Suzuki:

09160-06046
Washer
09160-06046 Washer
30ELE, 30ESE, 30MLE, DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15A, DF20A, DF40, DF40, DF40A, DF40QH, DF40TL, DF50, DF50, DF50A, DF50QH, DF50TL, D
09160-10082
Washer
09160-10082 Washer
30ELE, 30ESE, 30MLE, DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF15, DF15S, DF200T, DF200Z, DF225T, DF225Z, DF25, DF250A, DF250T, DF250Z, DF25
09160-06066
Washer
09160-06066 Washer
DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, DF225, DF225T, DF225Z, DF250, DF250, DF250, DF250T, DF250Z, DT15 MLE, DT150, DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT15
08322-01067
WASHER
08322-01067 WASHER
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF15, DF15, DF15S, DF4, DF4, DF4, DF46, DF4L, DF6, DF6, DF6, DF60, DF6L, DF70, DF9.9, DF9.9R, DF9.9RL, DF9.9S
08322-01087
WASHER
08322-01087 WASHER
DF200, DF200, DF200, DF225, DF225, DF225, DF250, DF250, DF250, DT115, DT140, DT150, DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, DT150STCLT, DT150TCLH, DT150TCLJ, DT150TCLK, DT150TCLL, DT150TCLM, DT1
32801-94402
09160-10080
 
09160-10080 WASHER (10x44x3)
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT40C
09169-06062
WASHER
09169-06062 WASHER
DF100, DF100, DF100, DF115, DF115, DF115, DF115TL, DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T, DF200Z, DF225, DF225, D
Back to top