54113-99JL0 Suzuki WASHER, UPR MOUNT BOLT

1. Disconnect the batteries. 2. Remove top panel (1), front panel (2) and the rear panel from the enclosure. 3. Remove the bolt holding ground wires (5) to the frame. Remove wire ties (4) to separate the ground wires. Remove two screws and cover (3). 4. Remove three bolts (7) to disconnect the power bars from the main circuit breaker. Remove the insulation material from power bar (6). Remove bolts (8) holding ground bar (9) to the panel. Put identification on the wires for assembly purposes.5. Disconnect wires (10) from the terminal strip. Disconnect wires (11) from the voltage regulator. 6. Disconnect wires (12) from the inside of the control panel. 7. Remove bolts (13) and disconnect the small gage wire from each power bar. 8. Disconnect wire loom (14) from the generator housing and from the inside of the enclosure at three places. Remove the bolts and lower panel (15). Be sure all wires are free from the enclosure 9. Attach Tooling (A) and a hoist to the enclosure as shown. Remove four bolts that fasten the enclosure to the base. Remove the enclosure. The weight of the enclosure is 259 kg (570 lb). The following steps are for the installation of the control panel enclosure.10. Use a hoist and Tooling (A) to put the enclosure in position on the base. Install the four bolts that hold it to the base.11. Connect wire loom (14) to the generator housing and to the inside of the enclosure at three places. Install lower panel (15).12. Connect small gage wire to each power bar with bolts (13).13. Connect wires (12) to the inside of the control panel.14. Connect wires (10) to the terminal strip. Connect wires (11) to the voltage regulator.15. Connect ground bar (9) to the panel with two bolts (8). Wrap insulation material around power bar (6). Connect the power bars to the main circuit breaker with three bolts (7).16. Connect ground wires (5) to the frame and install wire ties (4) to hold the wires together. Install cover (3) with two screws.17. Install the rear, front and top panels on the enclosure.18. Connect the batteries.Remove Control Panel Enclosure (Standby)
The photographs shown are of a 3306 Standby Generator. The procedure is the same for the 3406 Standby Generator. 1. Remove door (1).2. Remove two bolts (2) from cover (3). 3. Remove doors (4).4. Remove fourteen bolts (7) and cover (5).5. Remove the battery charger. See the topic "Remove & Install Battery Charger".6. Remove the bolts and cover (6).7. Remove the three bolts located above the control panel and remove cover (3). 8. Identify and disconnect all the wires from breaker (9) and grounding buss (10).9. Remove bolts (8), bracket (11), and breaker (9). 10. Identify and disconnect all wires (12) between the generator and the control panels from the terminal strips on the control panels.11. Identify and disconnect all wires between the engine and control panels from the terminal strips on the control panels.12. Remove bolts (13). 13. Install Tool (A) to enclosure (14) as shown, and fasten a hoist. It is necessary to remove one of the studs from the top of enclosure (14) before Tool (A) can be installed.14. Remove enclosure (14).Install Control Panel Enclosure. (Standby)
The photographs shown are of a 3306B Standby Generator. The procedure is the same for the 3406B Standby Generator. 1. Install Tool (A) to enclosure (14) as shown and fasten a hoist. It is necessary to remove one of the studs from the top of enclosure (14) before Tool (A) can be installed. 2. Put enclosure (14) in position on the base assembly for the generator set. Install bolts (13).3. Remove the hoist and Tool (A). Install the stud in the top of enclosure (14).4. Connect all wires (12) to the terminal strips on the control panels.5. Connect all the wires from the engine to the terminal strips on the control panels. 6. Put bracket (11) and breaker (9) in position and install bolts (8).7. Connect wires to breaker (9) and grounding buss (10). Install the battery charger. See the topic "Remove & Install Battery Charger". 8. Put cover (3) in position and install the three bolts above the control panel that hold cover (3) in place.9. Put cover (6) in position and install the bolts that holds it in place.10. Put cover (5) in position and install bolts (7). Install door (4). 11. Install two bolts (2) to cover (3). Install door (1).