36620-93J01 Suzuki WIRE ASSY, REMOTE CONTROL


36620-93J01 WIRE ASSY, REMOTE CONTROL Suzuki DF100, DF100, DF115, DF115, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF15, DF150, DF150, DF175, DF175, DF200, DF200, DF225, DF225, DF250, DF250, DF40, DF40, DF40A, DF50, DF50, DF50A, DF60, DF60A, DF70, DF70A, DF70A, DF80A, WIRE
36620-93J01 WIRE ASSY, REMOTE CONTROL Suzuki
Rating:
53

Buy WIRE ASSY, REMOTE CONTROL 36620-93J01 Suzuki genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$99.99

10-12-2024

CA: GuangYun Gongsi
Outboard Main Wiring Harness 36620-93J01 Plug and Play Control Box Wire Harness for Fourstroke Outboards DF40 to DF250 26.25ft
Srliya Fitment: Main wiring harness is fit for Fourstroke Outboards DF40 to DF250 (Non Ap Models), and is plug and play with all oem controls 2005 and newer. || OE Number: The part numbers of main wire harness for reference is 36620-93J01, please confirm whether it is consistent with the OE you need. || Connection: Specifically designed to fit your outboard control box, the Main Harness ensures an efficient and electrical connection, optimising the performance of your marine electrical system. || Easy to Install: The 36620-93J01 model is a great choice for anyone looking to upgrade their marine wiring system. Whether you're a professional sailor or a recreational sailor, this main wiring harness is an essential component to ensure your boat's electrical system runs smoothly. || Premium Material: Constructed from tough nylon, plastic, flexible rubber and highly conductive copper wire, our harnesses ensure both high conduction and longevity.
$112.99

10-12-2024
5.28[2.38] pounds
US: HTAOLI-US
16-Pin 20FT Control Main Wiring Harness 36620-93J01, Compatible for Suzuki, Reliable Wiring Solution, Direct Fit for Seamless Electrical Connectivity in Suzuki Models
denurfer ๐ŸŽ๏ธ Durable & High-Quality Construction: Made from durable plastics material, this 16-pin, 20ft control main wiring harness is built for long-lasting performance. Its high hardness ensures resistance to wear and tear, making it a reliable component for your Suzuki vehicle's electrical system. || ๐ŸŽ๏ธ Wide Compatibility: This control main wiring harness is compatible with a wide range of Suzuki models, offering a flexible and reliable solution for various electrical system needs. It ensures a seamless fit for your vehicle, making it an essential part for maintaining your Suzuki's electrical connections. || ๐ŸŽ๏ธ Easy Installation: Designed for a straightforward installation, this wiring harness is compatible with Suzuki models and allows for quick and efficient electrical connection. Professional installation is highly recommended to ensure a smooth installation process. || ๐ŸŽ๏ธ Manufactured to OE Specifications: Built to match OE part number 36620-93J01, this wiring harness ensures perfect compatibility with Suzuki vehicles. It is engineered to meet or exceed original equipment standards for optimal performance and longevity. || ๐ŸŽ๏ธ Comprehensive Package: The package includes the 16-pin, 20ft control main wiring harness, providing everything you need to restore or upgrade your vehicleโ€™s electrical system. This part will help maintain the performance and reliability of your Suzukiโ€™s electrical components.
$107.41

08-11-2024

US: Shanggu Keji
FAMUGOS Ouboard Black Control Main Wiring Harness 16 pins Replacement for Suzuki ZOYAN-36620-93J01 36620-93J01
FAMUGOS Package - 1 x Control Main Wiring Harness || Replaces Part Number - ZOYAN-36620-93J01 36620-93J01 || Fitment - Replacement For Suzuki || Installation - To achieve optimal performance of this product, it is strongly recommended to have a professional installation. || Note - Please check the picture and model again to make sure this item fits your vehicle. If have any question about this item, please send message with us, we will try to answer all the question you may have.
Number on catalog scheme: 10
 

Suzuki entire parts catalog list:

DF100 2009
DF100 2010
DF115 2001,2002,2003,2004,2005,2006,2007,2008,2009
DF115 2010
DF140 2002,2003,2004,2005,2006,2007
DF140 2008,2009,2010
DF140T 2002,2003,2004,2005,2006,2007,2008,2009
DF140T 2010
DF140Z 2002,2004,2005,2006,2007,2009
DF140Z 2003
DF140Z 2008
DF140Z 2010
DF15 2004,2005,2006,2007,2008,2009
DF15 2010
DF150 2006,2007,2008,2009
DF150 2010
DF175 2006,2007,2008,2009
DF175 2010
DF200 2004,2005,2006,2007,2008,2009
DF200 2010
DF225 2004,2005,2006,2007,2008,2009
DF225 2010
DF250 2004,2005,2006,2007,2008,2009
DF250 2010
DF40 1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF40 2010
DF40A 2010
DF50 1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF50 2010
DF50A 2010
DF60 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF60A 2010
DF70 1998,1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009
DF70A 2009
DF70A 2010
DF80A 2009
DF80A 2010
DF9.9R 2004,2005,2006,2007,2008,2009
DF9.9TH 2008
DF9.9TH 2009,2010
DF90 2001,2002,2003,2004,2005,2006,2007,2008
DF90A 2009
DF90A 2010
DF99R 2004,2005,2006,2007,2008,2009
DF99TH 2008,2009,2010

Information:


Illustration 1 g00755287
Schematic
Test Step 1. Inspect Electrical Connectors and Wiring
Illustration 2 g01089706
Terminal locations for ECM
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect the harness connector J1/P1 and the machine connector J3/P3. Also inspect the connections for the battery to the ECM. Inspect the connections from the keyswitch to the ECM. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the following connections:
P1:04 (+Battery (unswitched))
P1:05 (−Battery)
P1:06 (+Battery (switched))
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the harness and wiring for abrasions and for pinch points from the battery to the ECM. Also, check the harness and wiring for abrasions and for pinch points from the keyswitch to the ECM. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and connectors appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem with the connectors or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.STOPTest Step 2. Check the Battery Voltage at the ECM
Disconnect engine harness connector P1 from ECM connector J1.
Turn the battery disconnect switch to the ON position.
Turn the keyswitch to the ON position.
Measure the voltage between terminal P1:04 (+Battery (unswitched)) and engine ground.
Measure the voltage between terminal P1:06 (+Battery (switched)) and engine ground. Expected Result:The measured voltage is between 11.0 VDC and 13.5 VDC for a 12 volt system and between 22.0 VDC and 27.0 VDC for a 24 volt system.Results:
OK - The ECM is receiving the correct battery voltage.Repair: Verify that the negative battery wires from the ECM have continuity to the negative terminal of the battery. If necessary, repair the negative battery wires. If an intermittent condition is suspected, refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - The battery voltage at the ECM is out of normal range. Proceed to Test Step 3.
Not OK - The voltage at terminal P1:06 is out of normal range. Proceed to Test Step 5.Test Step 3. Check the Batteries
Measure no-load battery voltage at the battery posts.
Load test the batteries. Use the 4C-4911 Battery Load Tester. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries" and Special Instruction, SEHS7633, "Battery Test Procedure". Expected Result:The batteries pass the load test. The measured voltage is the minimum specification for a 12V or 24V system.Results:
OK - The battery voltage meets minimum specifications. Proceed to Test Step 4.
Not OK - The battery voltage does not meet minimum specifications.Repair: Recharge or replace the faulty batteries. Verify that the repair eliminates the problem.STOPTest Step 4. Check the Voltage from the 15 amp Circuit Breaker to the ECM
Measure the voltage from the 15 amp circuit breaker that is between the battery disconnect switch and the ECM. Measure the voltage between the 15 amp circuit breaker and engine ground. Expected Result:The measured voltage is between 11.0 VDC and 13.5 VDC for a 12 volt system and between 22.0 VDC and 27.0 VDC for a 24 volt system.Results:
OK - The correct voltage is present at the 15 amp circuit breaker.Repair: Repair the wiring between the 15 amp circuit breaker and the ECM connector P1. Refer to Illustration 1.STOP
Not OK - The correct voltage is not present at the 15 amp circuit breaker.Repair: Verify that the battery disconnect switch is in the ON position. Verify that the 15 amp circuit breaker is operating correctly. Repair the wiring between the battery and the 15 amp circuit breaker. Refer to Illustration 1.STOPTest Step 5. Check the Voltage from the Keyswitch to the ECM
Turn the keyswitch to the OFF/RESET position.
Remove the wire from terminal R of the keyswitch.
Turn the keyswitch to the ON position.
Measure the voltage on terminal B of the keyswitch to engine ground.
Measure the voltage on terminal R of the keyswitch to engine ground.
Turn the keyswitch to the OFF/RESET position. Expected Result:Voltage is present on terminal B and terminal R at the keyswitch.Results:
OK - Voltage is present on terminal B and terminal R at the keyswitch.Repair: If voltage is present on terminal R, repair the wire between the keyswitch and the ECM. Verify that the 15A breaker is not tripped. Return all wiring to the original configuration. Verify that the problem is eliminated.STOP
Not OK - Voltage is not present on terminal B at the keyswitch.Repair: If voltage is not present on terminal B, repair the wire between the +Battery and the keyswitch. Verify that the breaker is not tripped. Check the battery's no-load voltage. Return all wiring to the original configuration. Verify that the problem is eliminated.STOP
Not OK - Voltage is not present on terminal R at the keyswitch.Repair: If voltage is present on terminal B of the keyswitch but not present on terminal R, replace the keyswitch. Return all wiring to the original configuration. Verify that the problem is eliminated.STOP


Parts wire Suzuki:

36894-95201
 
36894-95201 WIRE LEAD
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF15, DF15, DF15, DF15S, DF25, DF25Q, DF25Q(QR), DF25T, DF30, DF30Q, DF30Q(QR), DF30T, DF40, DF40, DF40A,
36894-94401
 
36894-94401 WIRE LEAD
DF25, DF25Q, DF25Q(QR), DF25T, DF30, DF30Q, DF30Q(QR), DF30T, DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL, DT115, DT140, DT15C, DT40C, DT55CLF, DT55CRLG, DT55CRLJ, DT55CRLK, DT55CRLL, DT55CRSG, DT55CRSH, DT55HTCLH, DT55HTCLJ, DT55HTCLK, DT
36620-93J10
WIRE ASSY, REMOCON EXTENSION
36620-93J10 WIRE ASSY, REMOCON EXTENSION
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T,
36620-93J30
WIRE ASSY, REMOCON ADAPTER NO.2
36620-93J30 WIRE ASSY, REMOCON ADAPTER NO.2
DF100, DF100, DF100, DF100A, DF115, DF115, DF115, DF115A, DF115TL, DF140, DF140, DF140, DF140A, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF150TX, DF150ZX, DF175, DF175, DF175, DF175TX, DF175ZX, DF200, DF200, DF200, DF200T,
36620-93J20
WIRE ASSY, REMOCON ADAPTER NO.1
36620-93J20 WIRE ASSY, REMOCON ADAPTER NO.1
DF100, DF100, DF115, DF115, DF115TL, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL, DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL, DF90, DF90TL
36665-98J00
 
36665-98J00 WIRE, JUMPER
DF100, DF100, DF100, DF115, DF115, DF115, DF140, DF140, DF140, DF140T, DF140T, DF140Z, DF140Z, DF140Z, DF140Z, DF150, DF150, DF150, DF175, DF175, DF175, DF200, DF200, DF225, DF225, DF250, DF250, DF300, DF300, DF40, DF40, DF50, DF50, DF60, DF70, DF70A
36620-92E20
WIRE ASSY, REMOCON
36620-92E20 WIRE ASSY, REMOCON
DF25, DF25Q, DF25Q(QR), DF25T, DF30, DF30Q, DF30Q(QR), DF30T, DF40, DF40, DF40QH, DF40TL, DF50, DF50, DF50QH, DF50TL, DF60, DF60HL, DF60TL, DF70, DF70THL, DF70TL
36620-94J01
WIRE ASSY, REMOTE CONTROL
36620-94J01 WIRE ASSY, REMOTE CONTROL
DF15, DF15, DF15, DF15A, DF20A, DF25R, DF25R, DF8A, DF8AR, DF9.9, DF9.9A, DF9.9AR, DF9.9R, DF9.9TH, DF9.9TH, DF99AR, DF99R, DF99TH
Back to top