31110-87D51-0ED Suzuki YOKE ASSEMBLY


31110-87D51-0ED YOKE ASSEMBLY Suzuki DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, DT150STCLT, DT150TCLH, DT150TCLJ, DT150TCLK, DT150TCLL, DT150TCLM, DT150TCLN, DT150TCLP, DT150TCLR, DT150TCXGM, DT150TCXGN, DT150TCXGP, DT150TCXGR, DT150T YOKE
31110-87D51-0ED YOKE ASSEMBLY Suzuki
Rating:
33

Buy YOKE ASSEMBLY 31110-87D51-0ED Suzuki genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Suzuki entire parts catalog list:

DT150SSH 1987
DT150SSJ 1988
DT150SSK 1989
DT150SSL 1990
DT150SSM 1991
DT150SSN 1992
DT150STCLP 1993
DT150STCLR 1994
DT150STCLS 1995
DT150STCLT 1996
DT150TCLH 1987
DT150TCLJ 1988
DT150TCLK 1989
DT150TCLL 1990
DT150TCLM 1991
DT150TCLN 1992
DT150TCLP 1993
DT150TCLR 1994
DT150TCXGM 1991
DT150TCXGN 1992
DT150TCXGP 1993
DT150TCXGR 1994
DT150TCXGS 1995
DT150TCXGT 1996
DT150TCXH 1987
DT150TCXJ 1988
DT150TCXK 1989
DT150TCXL 1990
DT150TCXM 1991
DT150TCXN 1992
DT150TCXP 1993
DT150TCXR 1994
DT150TCXS 1995
DT150TCXT 1996

Information:

start by:a) remove fuel injection pump housing and governorb) remove adapter housing 1. Put the fuel injection pump housing and governor in position on tool (A).2. Remove bolts (1) that hold the governor housing (2) to the fuel injection pump housing. 3. Remove governor housing (2).4. Remove two bolts (3) from the cover. Remove cover (4) from over the torque spring. 5. Remove spring (7), wave washer (6) and guide (5) from the governor housing.6. Remove gasket (8) from the governor housing. 7. Remove bolt (11) and nut (9) from the torque spring (10). Remove the torque spring.8. Remove pin (12) from the hole in the fuel injection pump housing. 9. Remove seat (15) and over fueling spring (16) from the shaft.10. Pull shaft (13) up and remove lever (14). 11. Remove riser (follower) (18) from the shaft.12. Remove ring and lever (17) from the dowel. 13. Remove cover (19) with tool (B). Tool (B) can cause damage to cover. Always inspect the cover for damage and install a new cover if needed. 14. Install timing pin (20) to hold the camshaft from turning.15. Remove three bolts (21) that hold the flyweight assembly in position.16. Remove flyweight assembly (22).17. Remove the timing pin from the fuel injection pump housing.Connection Of Governor To Fuel Injection Pump Housing
1. Put the fuel injection pump housing on tool (A).2. Install timing pin (1) to hold the camshaft from turning.3. Put flyweight assembly (2) in position on the camshaft.
Make sure the pin that holds the shaft in the flyweight assembly is in position before installing the flyweight assembly.
4. Install three new bolts that hold the flyweight assembly to the camshaft. The bolts for holding the flyweight assembly to the camshaft have a locking material on the threads. The bolts must not be used more then one time. 5. Install cover (3) over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (4). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover.
7. Put lever (7) on the dowel. Install ring (6).8. Install pin (5) in the fuel injection pump housing with the round edge down. 9. Put the riser (follower) (11) in position between the flyweights. Lift the flyweights up with a piece of wire and push the riser (follower) forward.10. Put lever (10) in position in the groove of the riser (follower) (11) and the ball end engaged in the sleeve shaft lever (8). Install shaft (9) that holds the lever in position.
If lever (10) is not installed correctly, the governor can not operate and can cause the engine to overspeed.
11. Install over fueling spring (14) and seat (13) on the shaft.12. Install the torque spring (12). Install the bolt and nut that hold the torque spring in position. 13. Install guide (18), wave washer (16) and spring (17) in the governor housing.14. Put a new gasket (15) on the governor housing. 15. Install cover (19) over the torque spring. Install the two bolts that hold the cover in position.16. Put the governor housing on the fuel injection pump housing. Install the bolts that hold the governor housing in position.end by:a) install adapter housingb) install fuel injection pump housing and governor


Parts yoke Suzuki:

31110-87D60-0ED
 
31110-87D60-0ED YOKE ASSEMBLY
DT150, DT150SSH, DT150SSJ, DT150SSK, DT150SSL, DT150SSM, DT150SSN, DT150STCLP, DT150STCLR, DT150STCLS, DT150STCLT, DT150TCLH, DT150TCLJ, DT150TCLK, DT150TCLL, DT150TCLM, DT150TCLN, DT150TCLP, DT150TCLR, DT150TCXGM, DT150TCXGN, DT150TCXGP, DT150TCXGR,
Back to top