31110-94520-0ED YOKE ASSY (GRAY) Suzuki
DT115, DT140, DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT75TCLJ, DT75TCLK, DT75TCLL, DT75TCLM, DT75TCLN, DT75TCLP, DT75TCLR, DT75TCLS, DT75TC
YOKE
Price: query
Rating:
Compatible models:
DT115
DT140
DT35CRLH
DT35CRLJ
DT35CRLK
DT35CRSH
DT35CRSJ
DT35CRSK
DT35MCLH
DT35MCLJ
DT35MCLK
DT35MCSH
DT35MCSJ
DT35MCSK
DT35TCLH
DT35TCLJ
DT35TCLK
DT75TCLJ
DT75TCLK
DT75TCLL
DT75TCLM
DT75TCLN
DT75TCLP
DT75TCLR
DT75TCLS
DT75TCLT
DT75TCLV
DT85TCLJ
DT85TCLK
DT85TCLL
DT85TCLM
DT85TCLN
DT85TCLP
DT85TCLR
DT85TCLS
DT85TCLT
DT85TCLV
DT85TCLW
DT85TCLX
DT85TCLY
Suzuki
Suzuki entire parts catalog list:
- POWER UNIT (MODEL:86~89) » 31110-94520-0ED
- POWER UNIT (MODEL:86~89) » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- Power Unit » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
- POWER UNIT 88-89 » 31110-94520-0ED
Information:
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1P-2322     Combination Puller     1    
9S-9153 Puller Jaws     2    Start By:
Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".Note: In this removal procedure, the crankshaft gear is removed from the engine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00541470
Note: Rotate the crankshaft until the timing marks on the crankshaft gear, the camshaft gear, the fuel injection pump gear and the oil pump gear are aligned.
Use Tool (A) and remove crankshaft gear (1) .
Check the key on the crankshaft. If the key is damaged, use a new part for replacement.Installation Procedure 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been heated.
Use an oven and heat the crankshaft gear to a temperature of 150 °C (302 °F).
Wear eye protection in order to prevent possible personal injury while performing the following steps.
Note: Ensure that the marks on the timing gears are in alignment. Align the fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top center position when these marks are in alignment.
Install the crankshaft gear on the end of the crankshaft. Tap lightly with a rubber mallet or a brass hammer until the crankshaft gear is seated. Ensure that the crankshaft gear is seated against the shoulder on the crankshaft.Note: Ensure that the timing marks of the crankshaft gear are on the front.End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".Removal Procedure 2
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
A     1P-0820     Hydraulic Puller     1    
9U-6600 Hand Hydraulic Pump     1    
0S-2398 Step Plate     1    
3H-0465 Push Puller Plates     4    
8B-7549 Puller Leg     2    
1B-4207 Full Nut     2    
8B-7551 Bearing Puller     1    Start By:
Remove the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove".Note: In this removal procedure, the crankshaft gear is removed after the crankshaft is removed from the engine. The weight of the crankshaft is 39 kg (86 lb).
Illustration 2 g00541880
Use Tool (A) to remove crankshaft gear (1) from crankshaft (2) .Note: Do not remove the crankshaft by tapping with a hammer.Note: Be careful not to damage the finished surfaces on the crankshaft.
Check the key on the crankshaft. If the key is damaged, use a new part for replacement.Installation Procedure 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been heated.
Use an oven and heat the crankshaft gear to a temperature of 150 °C (302 °F).
Parts yoke Suzuki:
31110-94520-02M
31110-94520-02M Yoke Assembly
DT35CRLH, DT35CRLJ, DT35CRLK, DT35CRSH, DT35CRSJ, DT35CRSK, DT35MCLH, DT35MCLJ, DT35MCLK, DT35MCSH, DT35MCSJ, DT35MCSK, DT35TCLH, DT35TCLJ, DT35TCLK, DT55CLF, DT55CRLG, DT55CRSG, DT55CRSH, DT55HTCLH, DT55TCLG, DT55TCLH, DT55TCSG, DT55TCSH, DT65CRLG,
31110-94610-0ED
31110-94610-0ED YOKE ASSY
DT115, DT140, DT40C, DT55CRLJ, DT55CRLK, DT55CRLL, DT55HTCLJ, DT55HTCLK, DT55HTCLL, DT55TCLJ, DT55TCLK, DT55TCLL, DT55TCLM, DT55TCLN, DT55TCLP, DT55TCLR, DT55TCLS, DT55TCLT, DT55TCLV, DT65CRLJ, DT65CRLK, DT65CRLL, DT65HTCLK, DT65HTCLL, DT65TCLJ, DT65
31110-94900