3C7-61018-2 Tohatsu BOLT 10-120


3C7-61018-2 BOLT 10-120 Tohatsu MD115A2 BOLT
3C7-61018-2 BOLT 10-120 Tohatsu
Rating:
73

Buy BOLT 10-120 3C7-61018-2 Tohatsu genuine, new aftermarket parts with delivery
Number on catalog scheme: 34
 

Compatible models:

MD115A2   Tohatsu

Tohatsu entire parts catalog list:

MD115A2 2010,2012,2013,2014

Information:

Probable Causes
Driven equipment
Engine supports
Low compression (cylinder pressure)
Electronic unit injectors
Individual malfunctioning cylinderRecommended Actions
Note: When performing the following procedure, do not stand near the engine. The vibration may indicate an imminent component failure.Note: Complete the procedure in the order in which the steps are listed.
Table 1
Troubleshooting Test Steps Values Results
1. Driven Equipment
A. Inspect the mounting bolts for the driven equipment. Inspect the alignment and the balance of the driven equipment.
B. Inspect the coupling.
Driven equipment
Result The driven equipment and the alignment are not OK.
Repair: Repair or replace the driven equipment.
Result: The driven equipment and the alignment are OK.
Proceed to Test Step 2.
2. Engine Supports
A. Inspect the mounts and the brackets while you run the engine through the speed range. Look for mounts and brackets that are loose and/or broken.
B. Check the alignment of the following before operating the engine under load for any length of time:
Mounts
Coupling
Engine supports
Result: The mounts and brackets are loose and/or broken.
Replace the mounts and brackets that are loose and/or broken.
Result: The mounts and brackets are not loose and/or broken.
Proceed to Test Step 3.
3. Low Compression (Cylinder Pressure)
A. Perform a compression test. Refer to Systems Operation, Testing, and Adjusting, "Compression - Test".
Cylinder compression
Result: The results of the compression test are outside the specifications.
Repair: Investigate the cause and rectify any faults.
Note: Possible causes of low compression are shown in the following list:
Loose glow plugs
Faulty piston
Faulty piston rings
Worn cylinder bores
Worn valves
Faulty cylinder head gasket
Damaged cylinder head
Result: The results of the compression test are OK.
Proceed to Test Step 4.
4. Electronic Unit Injectors
A. Use the electronic service tool to perform the automatic "Cylinder Cutout Test".
Note: If the compression test that was performed in Test Step 3 was satisfactory, the "Cylinder Cutout Test" will identify any faulty injectors.
Electronic Unit Injectors
Result: A faulty injector is indicated.
Repair: Remove any faulty electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Install new electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Repeat the automatic "Cylinder Cutout Test". If the fault is still apparent, remove the replacement electronic unit injector and install the original electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and Disassembly and Assembly, "Electronic Unit Injector - Install".
Result: All injectors are OK.
Proceed to Test Step 5.
5. Individual Malfunctioning Cylinders
A. With the engine speed at a fast idle, use the electronic service tool to perform the manual "Cylinder Cutout Test".
As each cylinder is cut out, listen for a change in the sound from the engine. When a cylinder is cut out, there should be a noticeable change in the sound of the engine.
Note: If a change in the sound of the engine is not noted, the isolated cylinder is not operating under normal conditions. If the isolation of a cylinder results in a change in the sound that is less noticeable, the cylinder may be operating below normal performance.
Cylinders
Result: The test indicates a faulty cylinder.
Repair: Investigate the cause of the fault on any cylinder that is not operating. Investigate the cause of the fault on any cylinder that is operating below normal performance.
Result: The test indicates that all cylinders are OK.
Contact the Dealer Solutions Network (DSN).


Parts bolt Tohatsu:

910103-0616
BOLT
910103-0616 BOLT
M120A2, M140A2, M15D2, M18E2, M2.5A, M2.5A2, M25C3, M3.5A2, M3.5B2, M30A4, M40C, M4C, M5B, M5BS, M60C, M70C, M8B, M9.8B, M9.9D2, MD115A2, MD70B, MD70B, MD70B, MD75C2, MD90B, MD90B, MD90B, MD90C2, MFS15B2, MFS15B2, MFS15C, MFS15C, MFS18B2, MFS18B2, MF
910103-7630
 
910103-7630 BOLT
M115A2, M15D2, M18E2, M2.5A, M2.5A2, M3.5A2, M9.9D2, MD115A, MD115A2
910103-0830
BOLT
910103-0830 BOLT
M2.5A, M2.5A2, M25C3, M3.5A2, M3.5B2, M30A4, M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, M8B, M9.8B, MD115A2, MD50A, MFS4B, MFS5A2, MFS5B, MFS5B, MFS6A2, MFS6B, MFS6B
910103-6616
BOLT
910103-6616 BOLT
M115A2, M120A2, M140A2, M15D2, M18E2, M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, M8B, M9.8B, M9.9D2, MD115A, MD115A2, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD50B2, MD50B2, MD70B, MD70B, MD70B, MD90B, MD90
3C7-62133-2
 
3C7-62133-2 BOLT, 12P 1.25-L105
M115A2, M120A2, M140A2, M40D2, M40D2, M40D2, M50D2, M60C, M70C, MD115A, MD115A2, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD50B2, MD50B2, MD70B, MD70B, MD70B, MD75C2, MD90B, MD90B, MD90B, MD90C2, MFS25A, MFS25B, MFS25B, MFS25B
910121-7625
 
910121-7625 BOLT
M115A2, MD115A, MD115A2, MD70B, MD70B, MD70B, MD90B, MD90B, MD90B
9101E3-5612
BOLT
9101E3-5612 BOLT
MD115A2, MD40B2, MD40B2, MD50B2, MD50B2, MD70B, MD75C2, MD90B, MD90C2, MFS15C, MFS15C, MFS2.5B, MFS2.5B, MFS2.5B, MFS20C, MFS20C, MFS25B, MFS25B, MFS2B, MFS3.5B, MFS3.5B, MFS3.5B, MFS30B, MFS4B, MFS4C, MFS5B, MFS5C, MFS6B, MFS6C, MFS8A3, MFS8A3, MFS8
3B7-60001-4
 
3B7-60001-4 BOLT 10-40
MD115A2, MD40B2, MD40B2, MD50B2, MD50B2, MD70B, MD75C2, MD90B, MD90C2
Back to top