3C8-84963-0 Tohatsu BOLT, 3/8-43


3C8-84963-0 BOLT, 3/8-43 Tohatsu M40D2, M40D2, M40D2, M50D2, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD50B2, MD50B2 BOLT
3C8-84963-0 BOLT, 3/8-43 Tohatsu
Rating:
58

Buy BOLT, 3/8-43 3C8-84963-0 Tohatsu genuine, new aftermarket parts with delivery
Number on catalog scheme: 8-3
 

Compatible models:

Tohatsu entire parts catalog list:

M40D2 2003
M40D2 2004
M40D2 2005
M50D2 2003
MD40A 2003
MD40B 2003,2004,2005,2007,2008,2009,2010,2011
MD40B 2006
MD40B2 2010
MD40B2 2011,2012,2013,2014
MD50A 2003
MD50B 2003
MD50B 2004,2005,2007,2008,2009,2010,2011
MD50B 2006
MD50B2 2010
MD50B2 2011,2012,2013,2014

Information:


Illustration 1 g00897955
Rear view
Illustration 2 g00897965
Top view
Illustration 3 g00897954
Closed position
(1) Adjusting bolt (2) Thrust washer Width of groove in shaft for thrust washer ... 6.53 0.10 mm (0.2571 0.0039 inch)Thickness of thrust washer ... 6.00 0.05 mm (0.236 0.002 inch) (3) Locking nut (4) Plate (5) Bolt (6) Stop plate (7) Housing Bore in housing for shaft bearings ... 25.402 0.010 mm (1.0001 0.0004 inch)Outside diameter of shaft bearings ... 25.529 0.020 mm (1.0051 0.0008 inch) (8) Shaft (9) Choke plate (10) Bolt (11) Bearing Install the bearings so the lubrication fitting is in an accessible position.Lubricate the bearings with 5P-0960 Molybdenum Grease. (12) Bolt Apply 155-0695 Thread Lock Compound to the threads of the bolts prior to assembly. (13) Bolt Apply 4C-5599 Anti-Seize Compound to the threads and to the face of the bolts. (14) Nut Torque for nuts ... 25 6 N m (18 4 lb ft) (15) Rod Distance between the center bores of the rod ends ... 118 mm (4.646 inch) (16) Clevis Apply 4C-4030 Thread Lock Compound to the threads. (17) Nut Torque for nuts ... 25 6 N m (18 4 lb ft) (18) Nut Torque for nut ... 200 20 N m (150 15 lb ft) (19) Rod Distance between the center bores of the rod ends ... 389 mm (15.315 inch) (20) Actuator (21) Inlet port (22) Outlet port (A) Angle Angle for the lever in the fully closed position ... 27 degrees (B) Angle Angle for the lever in the fully closed position ... 45 degrees (C) Angle Angle for the lever in the fully closed position ... 34 degreesUse the following procedure to assemble the air choke:
Assemble choke plate (9) to shaft (8). Loosely install bolts (10).
Install thrust washer (2) and tighten bolts (5).
To ensure that bolts (10) are properly seated in shaft (8), fully close choke plate (9) and tighten bolts (10).
Make sure that choke plate (9) is fully closed. Loosen locking nut (3) and turn adjusting bolt (1) until the bolt is seated against stop plate (6). Tighten the bolt for an additional 1/4 turn (90 degrees) and then tighten the locking nut.
Assemble the actuator with inlet port (21) in the upward position and with outlet port (22) in the downward position. Tighten nut (18) to the specified torque.
Apply 4C-4030 Thread Lock Compound to the threads of clevis (16).
Assemble rod (15). Provide equal engagement of the threads at both ends of the rod until the distance between the center bores of the rod ends is approximately the specified length.
Assemble rod (19). Provide equal engagement of the threads at both ends of the rod until the distance between the center bores of the rod ends is approximately the specified length.
For final adjustment of the linkage, ensure that the actuator does not try to force stop plate (6) past plate (4) when the choke plate is moved to the fully open position.
Fully extend the actuator. Make sure that the choke plate is in the fully open position and that stop plate (6) contacts plate (4).
Then reduce the length of rod (15) by 1/2 turn (180 degrees). This allows a clearance between stop plate (6) and plate (4).
Make sure that the choke plate can achieve the fully closed position. Tighten nuts (14) and nuts (17) to the specified torque.


Parts bolt Tohatsu:

910114-0610
 
910114-0610 BOLT, CRANKCASE HEAD
M2.5A, M40D2, M40D2, M40D2, M50D2, M8B, M9.8B
910103-0830
BOLT
910103-0830 BOLT
M2.5A, M2.5A2, M25C3, M3.5A2, M3.5B2, M30A4, M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, M8B, M9.8B, MD115A2, MD50A, MFS4B, MFS5A2, MFS5B, MFS5B, MFS6A2, MFS6B, MFS6B
910114-0625
BOLT, CARRYING HANDLE
910114-0625 BOLT, CARRYING HANDLE
M15D2, M18E2, M2.5A, M25C3, M30A4, M40C, M40D2, M40D2, M40D2, M50D2, M60C, M70C, M9.9D2, MD40A, MD40B, MD40B, MD50A, MD50B, MD50B, MD50B
910113-5620
BOLT
910113-5620 BOLT
M115A2, M120A2, M140A2, M15D2, M18E2, M25C3, M30A4, M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, M9.9D2, MD115A, MD40A, MD40B, MD40B, MD50A, MD50B, MD50B, MD50B, MFS15B2, MFS15B2, MFS18B2, MFS18B2, MFS2.5A, MFS25A, MFS25B, MFS2A, MFS
910113-5616
 
910113-5616 BOLT
M115A2, M120A2, M140A2, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, MD115A, MD40A, MD40B, MD40B, MD50A, MD50B, MD50B, MD50B, MD70B, MD70B, MD70B, MD90B, MD90B, MD90B, MFS15B2, MFS15B2, MFS18B2, MFS18B2, MFS2.5A, MFS25A, MFS25B, MFS2A, MFS3.5A, MFS30A
910103-6616
BOLT
910103-6616 BOLT
M115A2, M120A2, M140A2, M15D2, M18E2, M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, M8B, M9.8B, M9.9D2, MD115A, MD115A2, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD50B2, MD50B2, MD70B, MD70B, MD70B, MD90B, MD90
910121-5620
BOLT
910121-5620 BOLT
M40D2, M40D2, M40D2, M50D2, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD50B2, MD50B2
3B7-60001-2
BOLT, 10-40
3B7-60001-2 BOLT, 10-40
M115A2, M120A2, M140A2, M60C, M70C, MD115A, MD50B, MD50B, MD70B, MD70B, MD70B, MD90B, MD90B, MD90B
Back to top