3V1-60108-0 Tohatsu BOLT, 6 - 16, PRE-COATED


3V1-60108-0 BOLT, 6 - 16, PRE-COATED Tohatsu MFS15C, MFS15C, MFS20C, MFS20C, MFS8A2, MFS8A3, MFS8A3, MFS8A3, MFS8A3, MFS9.8A2, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.9C BOLT
3V1-60108-0 BOLT, 6 - 16, PRE-COATED Tohatsu
Rating:
88

Buy BOLT, 6 - 16, PRE-COATED 3V1-60108-0 Tohatsu genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

Compatible models:

Tohatsu entire parts catalog list:

MFS15C 2008,2009,2011,2012,2013,2014
MFS15C 2010
MFS20C 2008,2009,2011,2012,2013,2014
MFS20C 2010
MFS8A2 2004,2005
MFS8A3 2006
MFS8A3 2007,2008,2009
MFS8A3 2010
MFS8A3 2011,2012,2013,2014
MFS9.8A2 2004,2005
MFS9.8A3 2006
MFS9.8A3 2007,2008,2009
MFS9.8A3 2010
MFS9.8A3 2011,2012,2013,2014
MFS9.9C 2008,2011

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
B 9U-7222 Camshaft Bearing Pilot 1
8M-8778 Taperlock Stud
1/2 - 13 by 1 9/16 inch 1
C 9U-7210 Puller Plate 1
D 9U-7223 Alignment Bushing 1
E 9U-7213 Backup Plate 1
0S-1621 Bolt
1/2 - 13 by 1 inch 1
F 9U-7214 Spacer Plate 1 Start By:
Remove the camshaft.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01159745
Remove the No. 7 camshaft bearing (rear). Work from the rear of the engine to the front of the engine.
Install the small end of Tooling (B) in camshaft bearing (1).
Position Tooling (C) over Tooling (A). Install Tooling (A) through the cylinder head on Tooling (B). Note: Tooling (C) is installed on the outside of the cylinder head. Tooling (C) is required in order to remove all the camshaft bearings from the cylinder head.
Use Tooling (A) to remove camshaft bearing (1) from the cylinder head.
Remove Tooling (B) from Tooling (A) and remove the camshaft bearing. Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01159754
Install the No. 7 camshaft bearing (rear), as follows:
Insert the large end of Tooling (B) into the No. 7 camshaft bore.
Position Tooling (C) over Tooling (A). Install Tooling (A) through the cylinder head on Tooling (B).
Position camshaft bearing (1) on Tooling (B). Install Tooling (E) on Tooling (B). Note: Refer to Specifications, "Cylinder Head" for appropriate information for the orientation of the camshaft bearings in the cylinder head.
Use Tooling (A) in order to pull camshaft bearing (1) into the camshaft bore. Note: When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.
Illustration 3 g01159756
Install the No. 6 through No. 2 camshaft bearings, as follows:
Insert the large end of Tooling (B) into the camshaft bore. Note: Use Tooling (D) to align Tooling (A) and Tooling (B) with the camshaft bearing bores. Install Tooling (D) in the inside diameter of any installed camshaft bearing between Tooling (A) and Tooling (B).
Install Tooling (A) on Tooling (B). Position camshaft bearing (1) on Tooling (B). Install Tooling (E) on Tooling (B). Note: Refer to Specifications, "Cylinder Head" for appropriate information for the location and the orientation of the camshaft bearings in the cylinder head.
Use Tooling (A) in order to pull camshaft bearing (1) into the camshaft bore. Note: When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed.
Illustration 4 g01159758
Install the No. 1 camshaft bearing (front), as follows:
Insert the large end of Tooling (B) into the No. 1 camshaft bore. Assemble Tooling (A) and Tooling (D) on Tooling (B).
Position camshaft bearing (1) on Tooling (B). Install Tooling (E) and Tooling (F) on Tooling (B). Note: Refer to Specifications, "Cylinder Head" for appropriate information for the location and the orientation of the camshaft bearings in the cylinder head.Note: Tooling (F) is used to seat the No. 1 camshaft bearing to the correct depth in the camshaft bore.
Use Tooling (A) in order to pull the No. 1 camshaft bearing into the No. 1 camshaft bore. When the chamfer of Tooling (E) contacts the face of the camshaft bore, the camshaft bearing is properly installed. End By:
Install the camshaft.


Parts bolt Tohatsu:

910103-5625
 
910103-5625 BOLT, DRIVE SHAFT HOUSING
M115A2, M120A2, M140A2, M15D2, M18E2, M2.5A, M2.5A2, M3.5A2, M3.5B2, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M8B, M9.8B, M9.9D2, MD115A, MD115A2, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD50B2, MD50B2, MD70B, MD70B, MD70B
910103-0616
BOLT
910103-0616 BOLT
M120A2, M140A2, M15D2, M18E2, M2.5A, M2.5A2, M25C3, M3.5A2, M3.5B2, M30A4, M40C, M4C, M5B, M5BS, M60C, M70C, M8B, M9.8B, M9.9D2, MD115A2, MD70B, MD70B, MD70B, MD75C2, MD90B, MD90B, MD90B, MD90C2, MFS15B2, MFS15B2, MFS15C, MFS15C, MFS18B2, MFS18B2, MF
910113-5620
BOLT
910113-5620 BOLT
M115A2, M120A2, M140A2, M15D2, M18E2, M25C3, M30A4, M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, M9.9D2, MD115A, MD40A, MD40B, MD40B, MD50A, MD50B, MD50B, MD50B, MFS15B2, MFS15B2, MFS18B2, MFS18B2, MFS2.5A, MFS25A, MFS25B, MFS2A, MFS
910113-0620
 
910113-0620 BOLT
M115A2, M120A2, M140A2, M40C, M40D2, M40D2, M40D2, M50D2, M60C, M70C, MD115A, MD40A, MD40B, MD40B, MD50A, MD50B, MD50B, MD50B, MD70B, MD70B, MD70B, MD90B, MD90B, MD90B, MFS15B2, MFS15B2, MFS18B2, MFS18B2, MFS25A, MFS25B, MFS30A, MFS30B, MFS4B, MFS4B,
3R3-07405-1
BOLT, DRAIN
3R3-07405-1 BOLT, DRAIN
MFS15B2, MFS15B2, MFS15C, MFS15C, MFS18B2, MFS18B2, MFS20C, MFS20C, MFS25A, MFS25B, MFS25B, MFS25B, MFS30A, MFS30B, MFS30B, MFS8A, MFS8A2, MFS8A3, MFS8A3, MFS8A3, MFS8A3, MFS9.8A, MFS9.8A2, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.9B2, MFS9.9B2,
3AA-60108-0
 
3AA-60108-0 BOLT, 6-20 PRECOATED
MFS15B2, MFS15B2, MFS15C, MFS15C, MFS18B2, MFS18B2, MFS20C, MFS20C, MFS25B, MFS25B, MFS25B, MFS30B, MFS30B, MFS8A2, MFS8A3, MFS8A3, MFS8A3, MFS8A3, MFS9.8A2, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.9B2, MFS9.9B2, MFS9.9C
3B7-77431-1
 
3B7-77431-1 BOLT
M40D2, M40D2, M40D2, M50D2, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD50B2, MD50B2, MFS15C, MFS20C, MFS25A, MFS25B, MFS25B, MFS25B, MFS30A, MFS30B, MFS30B, MFS8A3, MFS8A3, MFS8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3
9161E3-0650
 
9161E3-0650 BOLT
MFS2.5B, MFS2.5B, MFS2.5B, MFS2B, MFS3.5B, MFS3.5B, MFS3.5B, MFS8A3, MFS8A3, MFS8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3
Back to top