3AT-03200-0 Tohatsu CARBURETOR


3AT-03200-0 CARBURETOR Tohatsu MFS4B, MFS4B, MFS5B, MFS6B CARBURETOR
3AT-03200-0 CARBURETOR Tohatsu
Rating:
28

Buy CARBURETOR 3AT-03200-0 Tohatsu genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$63.39

14-08-2024

CN: Marine Parts Manufac
Boat Engine 3AT-03200-0 3AT032000 3AT032000M 3DJ-03200-0 3DJ032000 3DJ032000M Carburetor for Tohatsu for Nissan 4-stroke 4HP MFS4B NFS4B / 5041098 for Evinrude Johnson OMC BRP Outboard Motor
SouthMarine Fit Tohatsu & fit Nissan Part Number: 3AT-03200-0 3AT032000 3AT032000M 3DJ-03200-0 3DJ032000 3DJ032000M || Fit Tohatsu & for Nissan 3R1-03200-1 3AS-03200-0 3R1-03200-1-00 3GV-03200-0 3AS-03200-0 3R1032001M 3R1032000M 3AS032000M 3GV032000M || Fit Mercury 803522T 803522T01 803522T02, 803522T03, 803522T04-T06, 803522A04, 8M0053670, 853720T25 || Fit Evinrude Johnson OMC BRP Part Number: 5041098 || Fit Outboard Engine: 4-stroke 4HP MFS4B NFS4B || If you are unsure, please provide your engine serial number.
Number on catalog scheme: 1
 

Compatible models:

MFS4B   MFS5B   MFS6B   Tohatsu

Tohatsu entire parts catalog list:

MFS4B 2005,2006,2007,2008,2009
MFS4B 2010
MFS5B 2010
MFS6B 2010

Information:

Recommended Actions
Table 1
Troubleshooting Test Steps Values Results
1. Check the Air Inlet and Exhaust System
A. Check the air inlet system for restrictions and/or for leaks.
B. Ensure that the turbocharger is in good repair.
C. Check the exhaust system for restrictions.
Air Inlet and Exhaust System
Result: The air inlet and exhaust system is OK.
Proceed to Test Step 2.
Result: The air inlet and exhaust system is NOT OK.
Repair: Repair or replace any damaged or worn components in the air inlet and exhaust system.
2. Check the Engine Speed/Timing
A. Check the calibration of the engine speed/timing sensor. Refer to Troubleshooting, "Engine Speed/Timing Sensor - Calibrate".
B. Verify that the crankshaft and the camshaft drive gears are set with the proper orientation. Refer to the Disassembly and Assembly manual.
Engine Speed/Timing
Result: The engine speed/timing is OK.
Proceed to Test Step 3.
Result: The engine speed/timing is NOT OK.
Repair: Repair or replace any damaged or worn components.
3. Check the Atmospheric Pressure Sensor
A. Check the atmospheric pressure sensor for dirt and/or for debris. Remove any dirt and/or debris that is present.
50 kPa (7.25 psi) and 100 kPa (14.5 psi)
Result: The atmospheric pressure sensor is within range.
Proceed to Test Step 4.
Result: The atmospheric pressure sensor is not within range.
Repair: Replace the atmospheric pressure sensor.
4. Check the Intake Manifold Pressure Sensor, "Fuel Position", and/or "FRC Fuel Limit"
A. Monitor the status of "Fuel Position" and "Rated Fuel Limit" while the engine is operating under full load. If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the Electronic Control Module (ECM) is providing the correct control.
B. Verify that there are no active diagnostic codes for the intake manifold pressure sensor.
C. Monitor the status of "Intake Manifold Pressure" and "Atmospheric Pressure" on the Caterpillar Electronic Technician (ET). When the engine is not running, "Intake Manifold Pressure" should be 0 kPa (0 psi).
D. A problem with the "FRC Fuel Limit" will only cause black smoke during acceleration. A problem with the "FRC Fuel Limit" will not cause black smoke during steady state operation.
Intake Manifold Pressure Sensor, "Fuel Position", and/or "FRC Fuel Limit"
Result: The Intake Manifold Pressure Sensor, "Fuel Position", and/or "FRC Fuel Limit" are OK.
Proceed to Test Step 5.
Result: The Intake Manifold Pressure Sensor, "Fuel Position", and/or "FRC Fuel Limit" are NOT OK.
Repair: Repair or replace any damaged or worn components.
5. Check for the Correct Flash File
A.Verify that the correct flash file is installed. Refer to Troubleshooting, "Flash Programming" for information.
Flash File
Result: The correct flash file is installed.
Proceed to Test Step 6.
Result: The correct flash file is NOT installed.
Repair: Download and install the correct flash file.
6. Check the Fuel Quality
Note: Cold weather adversely affects the characteristics of the fuel. Refer to Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.
Fuel
Result: The fuel quality is OK.
Proceed to Test Step 7.
Result: The fuel quality is NOT OK.
Repair: Replace the fuel in the tank with new fuel.
7. Check the Valve Adjustment
A. Check the valve adjustment. Refer to Systems Operation/Testing and Adjusting for information on valve adjustments.
Valve Adjustment
Result: The valves are OK.
Return the engine to service.
Result: The valves are NOT OK.
Repair: Adjust the valves.


Parts carburetor Tohatsu:

3H9-03200-1
CARBURETOR ASSY
3H9-03200-1 CARBURETOR ASSY
MFS4A2, MFS4B, MFS4B
3R1-03200-1
CARBURETOR ASSY
3R1-03200-1 CARBURETOR ASSY
MFS5A2, MFS5B, MFS5B
3R4-03200-0
CARBURETOR ASSY
3R4-03200-0 CARBURETOR ASSY
MFS6A2, MFS6B, MFS6B
3H6-87122-0
CARBURETOR REPAIR KIT
3H6-87122-0 CARBURETOR REPAIR KIT
MFS4B, MFS4B, MFS4C, MFS5B, MFS5B, MFS5C, MFS6B, MFS6B, MFS6C
3AS-03200-0
CARBURETOR
3AS-03200-0 CARBURETOR
MFS4B, MFS5B, MFS5B, MFS6B
3AU-03200-0
CARBURETOR
3AU-03200-0 CARBURETOR
MFS4B, MFS5B, MFS6B, MFS6B
Back to top