3BH-67192-0 Tohatsu CHOKE LINK ROD

Table 1
Diagnostic Codes Table
Code and Description Conditions which Generate this Code System Response Procedure
268-2 Programmed Parameter Fault : Erratic, Intermittent, or Incorrect The Electronic Control Module (ECM) detects that one or more of the programmable parameters have not been programmed. The engine performance may be affected by unprogrammed parameters. The unprogrammed parameters determine the action that is taken by the ECM. The ECM may use a default torque map or the ECM may limit the engine to low idle. Program the missing parameter.
1495-2 Injector Trim Codes Not Programmed The ECM detects that one or more of the injector trim codes has not been programmed. The ECM has been powered for three seconds. The code is logged in memory. The engine will start. The ECM will use a default setting of 0000 for an unprogrammed injector trim code. Program the missing injector trim code. System configuration parameters are parameters that affect emissions and power of the engine. Default values for the parameters are programmed at the factory. Some parameters may be changed by the customer in order to suit the needs of the specific application. Values for these parameters can be viewed on Caterpillar Electronic Technician (ET). Certain configuration parameters are also stamped on the engine information plate.No password is required for programming a new ECM during the first 100 hours of service life. This 100 hour “free configuration” feature enables the customer to tailor the programmable setpoints to the requirements of the installation. Exceptions are "Fuel Limit" and "Personality Module Mismatch".Note: If the parameters that are protected with the factory passwords are changed, the Caterpillar warranty may be voided.If a programmable parameter has not been programmed, the ECM will generate a 268-2 diagnostic code. The unprogrammed parameters will be set to default. Certain aspects of the engine's performance and engine monitoring may be affected.If an injector code has not been programmed, the ECM will generate a 1495-2 diagnostic code. The injector code is a number that is found on each of the unit injectors. The ECM uses this number to compensate for manufacturing variations between individual injectors. If you replace any of the unit injectors, you must reprogram the code for the new injectors. Also, if you replace the ECM, you must reprogram all of the injector codes.Note: The injector codes are not part of the "Configuration" screen on the electronic service tool. "Injector Codes Calibration" can be found under "Calibrations" in the "Service" menu on Cat ET.Parameter Table
Table 2
System Configuration Parameters
Parameter Default Range Password
Required
"Personality Module Interlock" Yes
"ECM Serial Number" Yes
"Engine Serial Number" 00000000 8 alphanumeric numbers No
"Equipment ID" 00000000000000000 17 alphanumeric numbers No
"Full Load Setting (FLS)" 0 -128 to +127 Yes
"Full Torque Setting (FTS)" 0 -128 to +127 Yes
"Fuel Ratio Control Offset (FRC)" 0 −25 to 0 No
"Rated Fuel Positon (mm)" 14 The minimum rack is based on engine power. Yes
"Fuel Correction Factor (%)" 0 -25 to +25 No
"Low Idle (rpm)" 1000 810 to 1000 No
"Droop (%)" 0.0 0.0 to 10.0 No
"Governor Gain Factor" Engine rating 0 to 39,999 Yes
"Governor Minimum Stability Factor" Engine rating 0 to 39,999 Yes
"Governor Maximum Stability Factor" Engine rating 0 to 39,999 Yes
"Acceleration Delay on Start-up (sec)" 0 0 to 60 No
"Acceleration Rate (rpm/sec)" 250 5 to 2000 No
"Programmable Torque Scaling" The minimum rack is based on engine power. The minimum rack is based on engine power. Yes
"Engine Cooling System Configuration" SCAC SCAC or JWAC Yes
"Cold Cylinder Cutout" Disabled Enabled
Disabled No
"Cooldown Engine Speed (rpm)" 900 810 to 1800 No
"Engine Cooldown Duration (min)" 0 0 to 30 No
"Engine Prelube System Configuration" Automatic Automatic
Continuous
"Engine Continuous Prelube Interval (min)" 1 0 to 65503 No
"Crank Duration (sec)" 0 0 to 60 No
"Maximum Number of Crank Cycles" 0 0 to 10 No
"Crank Terminate Speed (rpm)" 400 100 to 500 No
"Total Tattletale" 0 0 to 255 N/A
"Intake Manifold Air Temperature Sensor Installation Status" Not Installed Installed
Not Installed
"Engine Oil Temperature Sensor Installation Status" Not Installed Installed
Not Installed
"Coolant Level Installation Status" Not Installed Installed
Not Installed
"Aftercooler Coolant Level Installation Status" Not Installed Installed
Not Installed
"Air Intake Shutoff Installation Status" Not Installed Installed
Not Installed
"Air Intake Shutoff Detection Installation Status" Not Installed Installed
Not Installed
Injector Code (1) 0000 4 numbers No
Injector Code (2) 0000 4 numbers No
Injector Code (3) 0000 4 numbers No
Injector Code (4) 0000 4 numbers No
Injector Code (5) 0000 4 numbers No
Injector Code (6) 0000 4 numbers No
Injector Code (7) 0000 4 numbers No
Injector Code (8) 0000 4 numbers No
Injector Code (9) 0000 4 numbers No
Injector Code (10) 0000 4 numbers No
Injector Code (11) 0000 4 numbers No
Injector Code (12) 0000 4 numbers No Parameter Descriptions
"Personality Module Interlock"
The "Personality Module Interlock" is automatically programmed by the ECM after factory passwords are entered."ECM Serial Number"
The "ECM Serial Number" is stored in the memory of the ECM. The "ECM Serial Number" can be accessed by the use of the service tool."Engine Serial Number"
Program the "Engine Serial Number" to match the engine serial number that is stamped on the engine information plate.Note: When you are requesting factory passwords, always use the engine serial number that is resident in the ECM.