369-83888-0 Tohatsu COLLAR, 13.5 - 18 - 2.5


369-83888-0 COLLAR, 13.5 - 18 - 2.5 Tohatsu M4C, M5B, M5BS, MFS4B, MFS5A2, MFS5B, MFS5B, MFS6A2, MFS6B, MFS6B COLLAR
369-83888-0 COLLAR, 13.5 - 18 - 2.5 Tohatsu
Rating:
33

Buy COLLAR, 13.5 - 18 - 2.5 369-83888-0 Tohatsu genuine, new aftermarket parts with delivery
Number on catalog scheme: 2-5
 

Compatible models:

Tohatsu entire parts catalog list:

M4C 2003
M5B 2003
M5BS 2003
MFS4B 2010
MFS5A2 2003,2004,2005
MFS5B 2005,2006,2007,2008,2009
MFS5B 2010
MFS6A2 2003,2004,2005
MFS6B 2005,2006,2007,2008,2009
MFS6B 2010

Information:


Illustration 1 g01181874
(1) BoltLubricate the threads of the bolt with 5P-3931 Anti-Seize Compound . Anti-Seize compound is not allowed on the bolt head, the face of the spacer, or the face of the impeller. Torque ... 370 N m (270 lb ft) (2) Spacer (3) Diameter of the shaft at the seat area of the seal assembly ... 44.450 0.020 mm (1.7500 .0008 inch) (4) Seal assembly
Stationary seal
Lubricate the O-ring and the face seal with clean water.
Use the 8T-3034 Water Pump Seal Driver and hand pressure in order to install the O-ring and the face seal as a unit in the pump housing bore. Ensure that the identification mark is oriented away from the seal group that is mounted on the shaft.
Rotating seal
Remove the spring from the seat.
Put clean water on the seal as the only lubrication for assembly. DO NOT get any grease or oil on the seal faces.
Do not stretch the rubber of the seal at installation. If the seal is stretched, the service life is shortened.
Use the 8T-3034 Water Pump Seal Driver and hand pressure in order to push the seal on the shaft until the seal face makes light contact.Note: The seal must rotate with the water pump shaft. Do not use any lubricant (except clean water) that will reduce the friction between the seal and the shaft.
Install the spring for the seal assembly. (5) Diameter of the impeller shaft at the location of the lip type seal ... 49.200 0.020 mm (1.9370 .0008 inch) (6) SealLubricate the bore of the housing for seal (6) with a light amount of glycerin or an equivalent. (7) Plug Torque ... 8 1 N m (70 9 lb in) (8) Diameter of impeller shaft ... 64.850 0.020 mm (2.5531 .0008 inch) (9) Diameter of the impeller shaft at the support end. ... 88.878 0.013 mm (3.4991 .0005 inch) (10) Thickness of thrust washer ... 11.85 0.05 mm (.467 .002 inch)Width of groove in the impeller shaft for the thrust washer ... 12.00 0.05 mm (.472 .002 inch)End play for impeller shaft ... 0.05 to 0.25 mm (.002 to .010 inch) (11) SealPut a light coat of glycerin on the O-ring seal at assembly. Put a light coat of glycerin in the housing bore at assembly.
Illustration 2 g01181918
(12) Bore in shaft support bearings ... 89.22 0.06 mm (3.512 0.002 inch) (13) Bore in impeller shaft bearings ... 65.15 0.060 mm (2.565 .0020 inch) (14) Dimension of bearings from surface of pump housing Dimension A ... 20 1 mm (0.7874 0.0394 inch) Dimension B ... 92.5 1 mm (3.6417 0.0394 inch) Dimension C ... 112.5 1 mm (4.4291 0.0394 inch) (15) The shaft support bearing should be flush with the surface of the pump housing during installation.
Illustration 3 g01181926
Positioning impeller shaft bearingsView A-A (16) Install the impeller shaft bearings with the bearing joint at a 5 degree angle from the horizontal centerline of the pump housing.
Illustration 4 g01181930
Positioning shaft support bearingsView B-B (17) Install the shaft support bearings with the bearing joint at a 15 degree angle from the vertical centerline of the pump housing.Coupling Assembly
Illustration 5 g01182055
Coupling assembly (1) Coupler shaft
Align 6 holes in coupler spring pack (4) with the 6 holes in coupler shaft (1) . Install the coupler spring pack and the coupler shaft to the pump shaft by using 6 bolts (5) . Tighten the bolts to 130 20 N m (96 15 lb ft).
Install drive gear assembly (6) to coupler spring pack (4) with 8 bolts (2) and 8 hard washers (3) . Tighten the bolts to 30 3 N m (22 2 lb ft).
Install coupler bearing cap (7) . Install bolt (8) to coupler shaft (1) . Tighten the bolt to 30 3 N m (22 2 lb ft).Adapter
Illustration 6 g01182067
(1) Pump assemblyDo not run the pump dry. (2) Adapter (3) DowelUse the dowels between the adapter and the pump assembly in order to aid in alignment. (4) Coupling assembly


Parts collar Tohatsu:

338-05255-0
 
338-05255-0 COLLAR, 4 - 6 - 21
M15D2, M18E2, M4C, M5B, M5BS, M8B, M9.8B, M9.9D2, MFS4A2, MFS5A2, MFS6A2, MFS8A, MFS9.8A
3R1-05215-0
 
3R1-05215-0 COLLAR, 6.1 - 8 - 6.5
M4C, M5B, M5BS, MFS4B, MFS4B, MFS4C, MFS5B, MFS5B, MFS5C, MFS6B, MFS6B, MFS6C, MFS8A, MFS8A2, MFS8A3, MFS8A3, MFS8A3, MFS8A3, MFS9.8A, MFS9.8A2, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3
3A0-76079-0
 
3A0-76079-0 COLLAR, 8.2 - 9 - 7.5
M25C3, M30A4, M40C, MFS15B2, MFS15B2, MFS15C, MFS15C, MFS18B2, MFS18B2, MFS2.5A, MFS2.5B, MFS2.5B, MFS2.5B, MFS20C, MFS20C, MFS25A, MFS25B, MFS25B, MFS25B, MFS2A, MFS2B, MFS3.5A, MFS3.5B, MFS3.5B, MFS3.5B, MFS30A, MFS30B, MFS30B, MFS4A2, MFS4B, MFS4B
3H6-76079-0
 
3H6-76079-0 COLLAR, 6.2 - 9- 7
MFS2.5A, MFS2A, MFS3.5A, MFS4A2, MFS4B, MFS4B, MFS5A2, MFS5B, MFS5B, MFS6A2, MFS6B, MFS6B
3R1-07439-0
 
3R1-07439-0 COLLAR, BREATHER
MFS4A2, MFS4B, MFS4B, MFS4C, MFS5A2, MFS5B, MFS5B, MFS5C, MFS6A2, MFS6B, MFS6B, MFS6C
3H6-63618-0
 
3H6-63618-0 COLLAR, DRUM
MFS2.5A, MFS2.5B, MFS2.5B, MFS2.5B, MFS2A, MFS2B, MFS3.5A, MFS3.5B, MFS3.5B, MFS3.5B, MFS4A2, MFS4B, MFS4B, MFS4C, MFS5A2, MFS5B, MFS5B, MFS5C, MFS6A2, MFS6B, MFS6B, MFS6C, MSF2A
3H6-63619-1
 
3H6-63619-1 COLLAR, BRACKET
M115A2, MD115A, MD115A2, MFS15B2, MFS15B2, MFS15C, MFS15C, MFS18B2, MFS18B2, MFS20C, MFS20C, MFS4A2, MFS4B, MFS4B, MFS5A2, MFS5B, MFS5B, MFS6A2, MFS6B, MFS6B, MFS8A3, MFS8A3, MFS8A3, MFS8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.9B2, MFS9.9B2,
3H6-05215-0
 
3H6-05215-0 COLLAR, 6.1-6-6.5
MFS4A2, MFS5A2, MFS6A2
Back to top