3AS-64331-0 Tohatsu DRIVE SHAFT BUSHING ASSY


3AS-64331-0 DRIVE SHAFT BUSHING ASSY Tohatsu MFS4B, MFS4B, MFS4C, MFS5B, MFS5B, MFS5C, MFS6B, MFS6B, MFS6C DRIVE
3AS-64331-0 DRIVE SHAFT BUSHING ASSY Tohatsu
Rating:
58

Buy DRIVE SHAFT BUSHING ASSY 3AS-64331-0 Tohatsu genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Compatible models:

Tohatsu entire parts catalog list:

MFS4B 2005,2006,2007,2008,2009
MFS4B 2010
MFS4C 2011,2012,2013,2014
MFS5B 2005,2006,2007,2008,2009
MFS5B 2010
MFS5C 2011,2012,2013,2014
MFS6B 2005,2006,2007,2008,2009
MFS6B 2010
MFS6C 2011,2012,2013,2014

Information:

Probable Causes
Active codes and logged codes
Electrical connections
Unstable fuel supply
Switches
Circuit protection
Engine speed/timing
Table 1
Associated Diagnostic Trouble Codes
J1939 Code CDL Code
3719-0 E995 (3)
3719-16 E995 (2) Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 2
Troubleshooting Test Steps Values Results
1. Active Codes and Logged Codes
A. Certain diagnostic codes and/or event codes may cause an engine shutdown. Connect the electronic service tool and check for active codes and for logged codes.
B. Use the electronic service tool to check for associated diagnostic trouble codes. Refer to Table 1
Codes
Result: There are associated diagnostic trouble codes active or logged.
Repair: Troubleshoot any active or logged associated diagnostic trouble codes before continuing with this procedure.
Result: There are no associated diagnostic trouble codes active or logged.
Proceed to Test Step 2.
2. Electrical Connections
A. Check for the correct installation of the ECM J1/P1 and the J2/P2 connectors. Check for correct installation of the fuel injector connectors.
Connectors
Result: There are suspect connectors.
Repair: Perform the "Wiggle Test" on the electronic service tool.
Repair or replace connectors that are suspect.
Result: There are no suspect connectors.
Proceed to Test Step 3.
3. Electrical Connections
A. Check the power and ground connections to the ECM. Refer to Troubleshooting, "Electrical Power Supply - Test".
Electrical Connectors
Result: The electrical connections are OK.
Proceed to Test Step 4.
Result: The electrical connections are not OK.
Repair: Repair or replace the damaged connectors. Verify that the repair eliminated the fault.
4. Unstable Fuel Supply
A. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information.
Cold weather adversely affects the characteristics of the fuel. Refer to the engine Operation and Maintenance Manual, "Cold Weather Operation" for further information.
B. Check fuel quality. Check the fuel tank for debris or foreign objects which may block the fuel supply.
Fuel
Result: The fuel quality is OK.
Proceed to Test Step 5.
Result: The fuel quality is not OK.
Repair: Replace the fuel. Verify that the repair eliminated the fault.
5. Switches
A. Check the keyswitch input to the ECM.
B. Check any engine shutdown switches and associated wiring.
Switches
Result: The shutdown switches and wiring are OK.
Proceed to Test Step 6.
Result: The shutdown switches and wiring are not OK.
Repair: Make the necessary repairs, Verify that the repair eliminated the fault.
6. Circuit Protection
A. Inspect the wires and connectors to all circuit protection for the engine.
B. Check the device for circuit protection.
Circuit protection
Result A circuit protection device is tripped.
Repair: Reset the circuit breaker if a circuit breaker is tripped. If necessary, replace blown fuses. Prior to returning the engine to service, determine the condition that caused the circuit breaker to trip or the fuse to blow. Make the necessary repairs.
Result The circuit protection is OK.
Proceed to Test Step 7.
8. Engine Speed/Timing Sensors
A. Inspect the connectors for the engine speed/timing sensors.
B. Crank the engine. If the engine starts and no speed timing codes are logged, the speed timing circuit is operating correctly.
Speed/Timing
Result: The Speed/Timing sensor circuit is not operating correctly.
Repair: Test the speed/timing circuit. Refer to Troubleshooting, "Speed/Timing `- Test". Verify that the repair eliminated the fault.
If the fault is still present, contact the Dealer Solutions Network (DSN).


Parts drive Tohatsu:

369-64303-0
 
369-64303-0 DRIVE SHAFT "UL"
M4C, M5B, M5BS, MFS4B, MFS4B, MFS4C, MFS5B, MFS5B, MFS5C, MFS6B, MFS6B, MFS6C
369-64301-0
DRIVE SHAFT "S"
369-64301-0 DRIVE SHAFT "S"
M4C, M5B, M5BS, MFS4A2, MFS4B, MFS4B, MFS4C, MFS5A2, MFS5B, MFS5B, MFS5C, MFS6A2, MFS6B, MFS6B, MFS6C
369-64302-0
 
369-64302-0 DRIVE SHAFT "L"
M4C, M5B, M5BS, MFS4A2, MFS4B, MFS4B, MFS4C, MFS5A2, MFS5B, MFS5B, MFS5C, MFS6A2, MFS6B, MFS6B, MFS6C
3h6Q61030-1
 
3h6Q61030-1 DRIVE SHAFT HOUSING "L"
MFS4B, MFS4B, MFS5B, MFS5B, MFS6B, MFS6B
3H6Q61020-0
 
3H6Q61020-0 DRIVE SHAFT HOUSING "S"
MFS4B, MFS4B, MFS5B, MFS5B, MFS6B, MFS6B
369-64331-2
 
369-64331-2 DRIVE SHAFT BUSHING ASSY
MFS4B, MFS4B, MFS4C, MFS5B, MFS5B, MFS5C, MFS6B, MFS6B, MFS6C
3AS-60003-0
 
3AS-60003-0 DRIVE SHAFT BUSHIN
MFS4B, MFS4B, MFS5B, MFS5B, MFS6B, MFS6B
369-64332-1
 
369-64332-1 DRIVE SHAFT BUSHING STOPPER
MFS4B, MFS4B, MFS4C, MFS5B, MFS5B, MFS5C, MFS6B, MFS6B, MFS6C
Back to top