3C7-64302-3 Tohatsu DRIVE SHAFT L


3C7-64302-3 DRIVE SHAFT L Tohatsu MD115A2, MD70B, MD75C2, MD90B, MD90C2 DRIVE
3C7-64302-3 DRIVE SHAFT L Tohatsu
Rating:
68

Buy DRIVE SHAFT L 3C7-64302-3 Tohatsu genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Compatible models:

Tohatsu entire parts catalog list:

MD115A2 2010,2012,2013,2014
MD70B 2010
MD75C2 2010,2011,2012,2013,2014
MD90B 2010
MD90C2 2010,2011,2012,2013,2014

Information:

Recommended Actions
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Note: The procedures have been listed in order of probability. Complete the procedures in order.Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load, and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.
Table 1
Troubleshooting Test Steps Values Results
1. Diagnostic Codes
Note: Certain diagnostic codes and/or event codes may cause poor performance. Refer to in the electronic service tool.
A. Use the electronic service tool to check for active or logged codes.
B. Use the electronic service tool to check the histogram information if the engine has been derated.
Note: If the histograms contain engine derates and no diagnostic codes are present, then the engine is operating normally.
Engine Derate or Diagnostic Codes
Result: A diagnostic code is present.
Repair: Troubleshoot the code and then reset the histogram.
Result: A diagnostic code is not present.
Proceed to Test Step 2.
2. Parameters in the Electronic Control Module (ECM)
A. Use the electronic service tool to verify that the correct parameters are being used. Refer to Troubleshooting, "Configuration Parameters" for additional information.
Parameters
Result: The parameters are not correct.
Repair: Input the correct parameters. Refer to Troubleshooting, "Configuration Parameters" for additional information.
Result: The parameters are correct.
Proceed to Test Step 3.
3. Throttle Signal
A. Monitor the status for "Throttle Position" on the electronic service tool. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed.
Throttle signal
Result: The throttle signal is stable.
Proceed to Test Step 4.
Result: The throttle signal is not stable.
Repair: Make the necessary repairs, Refer to the appropriate circuit test for the type of speed control that is installed.
4. Air Intake and Exhaust System
A. Observe the check engine lamp. Check for an air filter restriction indicator, if equipped. Replace a plugged air filters. Refer to the Operation and Maintenance Manual.
B. Check the air inlet and exhaust system for restrictions and/or leaks.
Restrictions
Result: There are restrictions in the air inlet or exhaust system.
Repair: Make the necessary repairs, Refer to Systems Operation/Testing and Adjusting, "Air Inlet and Exhaust System - Inspect" for additional information.
Result: There are no restrictions in the air inlet or exhaust system.
For engines with a single turbocharger, proceed to Test Step 5.
For engines with two turbochargers, proceed to Test Step 6.
5. Turbocharger
This Test Step is applicable to engines with a single turbocharger.
Note: The turbocharger that is installed on the engine is a nonserviceable item. If any mechanical fault exists, then the faulty turbocharger must be replaced.
A. Ensure that the mounting bolts for the turbocharger are tight.
B. Check that the oil drain for the turbocharger is not blocked or restricted.
C. Check that the compressor housing for the turbocharger is free of dirt and debris. Make sure that the housing is not damaged.
D. Check that the turbine housing for the turbocharger is free of dirt and debris. Make sure that the housing is not damaged.
E. Check that the turbine blades rotate freely in the turbocharger.
F. Ensure that the wastegate on the turbocharger is adjusted correctly. Refer to Systems Operation, Testing, and Adjusting, "Turbocharger - Inspect". If the wastegate actuator is faulty, replace the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" and Disassembly and Assembly, "Turbocharger - Install".
Turbocharger
Result: There is a fault on the turbocharger.
Repair: Repair the turbocharger or replace the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" and Disassembly and Assembly, "Turbocharger - Install".
Result: The turbocharger


Parts drive Tohatsu:

353-72406-0
 
353-72406-0 DRIVE CLEANER
M115A2, M120A2, M140A2, M40C, M40D2, M40D2, M40D2, M50D2, M60C, M70C, MD115A, MD115A2, MD40A, MD40B, MD40B, MD40B2, MD50A, MD50B, MD50B, MD50B, MD50B2, MD70B, MD70B, MD70B, MD90B, MD90B, MD90B
3T9-10060-0
 
3T9-10060-0 DRIVE PULLEY
MD40A, MD40B, MD50A, MD50B, MD50B, MD70B, MD70B, MD70B, MD90B, MD90B, MD90B
3E0-64236-0
 
3E0-64236-0 DRIVE SLEEVE
M120A2, M140A2, M60C, M70C, MD70B, MD70B, MD90B, MD90B
3T9-10061-0
 
3T9-10061-0 DRIVE BELT
MD70B, MD70B, MD70B, MD90B, MD90B, MD90B
3C7-64303-0
 
3C7-64303-0 DRIVE SHAFT UL
MD70B, MD70B, MD70B, MD90B, MD90B, MD90B
3FWQ61192-0
 
3FWQ61192-0 DRIVE SHAFT HOUSING
MD70B, MD75C2, MD90B, MD90C2
3C7-64303-3
 
3C7-64303-3 DRIVE SHAFT UL
MD115A2, MD70B, MD75C2, MD90B, MD90C2
Back to top