3C7B87110-1 Tohatsu ENGINE SHORT BLOCK


3C7B87110-1 ENGINE SHORT BLOCK Tohatsu M120A2, M140A2 ENGINE
3C7B87110-1 ENGINE SHORT BLOCK Tohatsu
Rating:
13

Buy ENGINE SHORT BLOCK 3C7B87110-1 Tohatsu genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

M120A2   M140A2   Tohatsu

Tohatsu entire parts catalog list:

M120A2 2003
M140A2 2003,2004,2005

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B 9U-5023 Main Bearing Wrench 1
C 2P-5517 Main Bearing Tool 1
D 236-6688 Main Bearing Cap Tool 2
E 9S-7351 Torque Wrench 1
F 8T-5096 Dial Indicator Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the main bearings dry when clearance checks are preformed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.
Illustration 1 g01125211
Install lower main bearing (4) in main bearing cap (2). Ensure that the main bearing is installed so that the bearing tab fits into the notch in the main bearing cap. Note: The main bearing caps must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.
Install the upper main bearing with the side without the tab into the side of the cylinder block with the tab. Use your hand and roll the upper main bearing into position. Use Tooling (A) and rotate the crankshaft. Rotate the crankshaft until the oil hole is positioned in front of the side of the upper main bearing with the tab.
Illustration 2 g01125209
Install Tooling (C) and finish rolling the upper main bearing into position. Make sure that Tooling (C) does not slide under the upper main bearing. Ensure that the main bearing is installed so that the bearing tab fits into the notch in the cylinder block.
Remove Tooling (C).
The following step is for installing the thrust plates on each side of the center main bearing. Place clean engine oil on the thrust plates. Install the thrust plates on each side of the center main bearing. It may be necessary to move the crankshaft with a prybar in order to install a new thrust bearing. Use Tooling (F) to measure the end play of the crankshaft. The end play must not exceed 0.17 to 0.63 mm (0.007 to 0.025 inch).
Illustration 3 g01125192
Tighten the nuts on Tooling (D) in order to raise main bearing cap (2) to the cylinder block. The nuts must be tightened evenly in order for main bearing cap (2) to fit into the block.
Coat the underside of the bolt heads and the threads of bolts (3) with clean engine oil. Install the inner bolts for the main bearing cap. Remove Tooling (D) and install the outer bolts for the main bearing cap.
Illustration 4 g01139473
Illustration 5 g01124192
Bolt tightening sequence for the main bearing caps
Use Tooling (E) and Tooling (B) and tighten bolts (3) in sequence to a torque of 190 14 N m (140 10 lb ft).
Place an index mark on the bolts and the main bearing cap. Tighten the bolts for an additional 180 5 degrees (1/2 turn).
Rotate the crankshaft in order to ensure that the crankshaft turns freely.
Illustration 6 g01125228
Install side covers (1) onto the cylinder block. End By:
Install the oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".


Parts engine Tohatsu:

3C7-01303-0
ENGINE BASEMENT GASKET
3C7-01303-0 ENGINE BASEMENT GASKET
M115A2, M120A2, M140A2, MD115A
3C7S01301-0
 
3C7S01301-0 ENGINE BASE
M120A2, M140A2
Back to top