3Z4-72573-0 Tohatsu EXTENSION CORD, TRIM SENSOR, LENGTH: 2000


3Z4-72573-0 EXTENSION CORD, TRIM SENSOR, LENGTH: 2000 Tohatsu MD115A2, MD40B2, MD40B2, MD50B2, MD50B2, MD70B, MD75C2, MD90B, MD90C2 EXTENSION
3Z4-72573-0 EXTENSION CORD, TRIM SENSOR, LENGTH: 2000 Tohatsu
Rating:
83

Buy EXTENSION CORD, TRIM SENSOR, LENGTH: 2000 3Z4-72573-0 Tohatsu genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Compatible models:

Tohatsu entire parts catalog list:

MD115A2 2010,2012,2013,2014
MD40B2 2010
MD40B2 2011,2012,2013,2014
MD50B2 2010
MD50B2 2011,2012,2013,2014
MD70B 2010
MD75C2 2010,2011,2012,2013,2014
MD90B 2010
MD90C2 2010,2011,2012,2013,2014

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
B     8T-3034     Water Pump Seal Driver     1    
C     169-5464     Quick Cure Primer     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.
Use steel wool to remove the deposits and the corrosion from the shaft.
Do not use sandpaper that will leave visible scratches on the pump shaft.
Inspect the area of the shaft that contacts the carbon seal rubber. Replace the shaft only if one of the following conditions exist in this area: pitting, corrosion and scoring. These conditions can provide a path for the leakage of coolant between the rubber and the pump shaft. If the shaft is polished in this area, this polishing indicates that the carbon seal assembly was spinning on the shaft. Use a fine grit sandpaper on the polished area before you install the new seal assembly.
Use Tooling (C) to clean the shaft and the seal counterbore in the housing.
Illustration 1 g01206688
Clean water only is permitted for use as a lubricant for assistance at installation. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
Apply clean water to the portion of ceramic seal in seal group (10) that is covered by the O-ring seal.
Immerse the carbon seal in seal group (10) in clean water. Install the carbon seal in seal group (10) on the shaft. Use Tooling (B) and hand pressure to push the carbon seal in seal group (10) onto the shaft until the face of the carbon seal makes contact with the ceramic seal face.
Position the spring in seal group (10) on the shaft.
Position impeller (7) on the shaft and install washer (6) and bolt (5) .
Tighten bolt (5) to a torque of 360 50 N m (270 37 lb ft). Hit the head of the bolt with a hammer and tighten the bolt again. Repeat this procedure until there is no change in the bolt torque.
Install a new O-ring seal (8) on the housing. Apply liquid soap to the O-ring seal.Note: Ensure that housing (4) is properly oriented when the housing is installed on the water pump.
Install housing (4) and bolts (9) on the water pump.
Illustration 2 g00605429
Install the coupling and flange (3) .
Install elbow (1). Connect elbow (1) to the tube and water pump (2) .
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".


Parts extension Tohatsu:

3A3-72573-0
EXTENSION CORD, TRIM METER
3A3-72573-0 EXTENSION CORD, TRIM METER
M115A2, M40D2, M40D2, M40D2, M50D2, M60C, M70C, MD115A, MD40A, MD40B, MD40B, MD50A, MD50B, MD50B, MD50B, MD70B, MD70B, MD70B, MD90B, MD90B, MD90B
3F3-72573-1
EXTENSION CORD, TRIM SENDER
3F3-72573-1 EXTENSION CORD, TRIM SENDER
M115A2, M60C, M70C, MD115A, MD40B, MD50B, MD70B, MD70B, MD70B, MD90B, MD90B, MD90B, MFS25B, MFS30B
3B7S61110-0
 
3B7S61110-0 EXTENSION HOUSING "UL"
M120A2, M140A2, M60C, M70C, MD70B, MD70B, MD90B, MD90B
3Y9S87314-0
 
3Y9S87314-0 EXTENSION HOUSING KIT UL
MD70B, MD70B, MD90B, MD90B
3T9S87314-0
 
3T9S87314-0 EXTENSION HOUSING KIT UL
MD70B, MD70B, MD90B, MD90B
3B7Q61110-0
 
3B7Q61110-0 EXTENSION HOUSING "UL"
M115A2, MD115A, MD115A2, MD40B, MD50B, MD70B, MD70B, MD75C2, MD90B, MD90B, MD90C2
3T5-71042-0
 
3T5-71042-0 EXTENSION CORD (LAMP)
M115A2, MD115A, MD40B2, MD40B2, MD50B2, MD50B2
3C8Q61110-0
 
3C8Q61110-0 EXTENSION HOUSING "UL"
MD40B, MD40B2, MD40B2, MD50B, MD50B2, MD50B2
Back to top