346-76015-0 Tohatsu PINION


346-76015-0 PINION Tohatsu M25C3, M30A4, M40C PINION
346-76015-0 PINION Tohatsu
Rating:
33

Buy PINION 346-76015-0 Tohatsu genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$149.99
 

05-01-2024
0.63[0.28] pounds
US: In Stock Motorsports
Pinion Assembly
Tohatsu Genuine OEM Tohatsu Part || OEM Pinion Assembly || Part Number: 346-76015-0 || May not include original package.
Number on catalog scheme: 1-1
 

Compatible models:

M25C3   M30A4   M40C   Tohatsu

Tohatsu entire parts catalog list:

M25C3 2003,2005
M30A4 2003
M40C 2004

Information:


Illustration 1 g01402736
Note: Use clean engine oil to lubricate the threads of the cylinder head bolts before assembly.Use the following procedure to tighten the cylinder head bolts:
Torque for bolt (1) through bolt (14) in a numerical sequence to 270 27 N m (200 20 lb ft)
Again torque the bolt (1) through bolt (14) in a numerical sequence to 450 20 N m (330 15 lb ft).
Finally torque the bolt (1) through bolt (14) in a numerical sequence to 450 20 N m (330 15 lb ft).
Install the rocker arm assemblies onto the cylinder head.
Torque the bolt (15) through bolt (18) in a numerical sequence to 270 27 N m (200 20 lb ft).
Again torque the bolt (15) through bolt (18) in a numerical sequence to 450 20 N m (330 15 lb ft).
Finally torque the bolt (15) through bolt (18) in a numerical sequence to 450 20 N m (330 15 lb ft).Note: Tighten the bolt (19) through bolt (27) only after the cylinder head bolts have been given final torque.
Torque for bolt (19) through bolt (27) at any tightening sequence to 43 7 N m (32 5 lb ft)
Illustration 2 g01017447
(A) Dimensions for the cylinder head Height of new cylinder head ... 112.78 0.25 mm (4.440 0.010 inch) Minimum height ... 111.51 mm (4.390 inch)
Illustration 3 g01388111
Note: Use 6V-6640 Sealant on the cup plugs. (D) The cup plugs are installed into the cylinder head at the following depth. ... 4.5 0.5 mm (0.18 0.02 inch) (E) The cup plugs are installed into the cylinder head at the following depth. ... 2.0 0.5 mm (0.08 0.02 inch)
Illustration 4 g01402732
Note: Apply liquid soap (40% solid) to the O-ring seal (29) and to the bore of the cylinder head prior to installation of the adapter.Note: Apply 4C-5599 Anti-Seize Compound onto the threads of the adapter prior to installation. (28) Torque for adapter ... 95 7 N m (70 5 lb ft)
Illustration 5 g01402737
Note: Use clean engine oil to lubricate the threads of the bolts prior to installation.Note: Tighten the bolts only after the cylinder head bolts have been given final torque. (30) Use the following procedure to tighten the bolts:
Position the housing support over the bolt holes that are in the cylinder head. Install the bolts (30) through the supports. Finger tighten the bolts.
Install the timing gear housing to the supports and tighten the bolts.
Torque the bolts (30) to 43 7 N m (32 5 lb ft).Note: Use 6V-6640 Sealant on the cup plugs. (F) Install the cup plugs in the front and rear side of each cylinder head to the following distance. ... 2.5 0.8 mm (0.10 0.03 inch)Note: Do not install cup plugs in rear side of each cylinder head for the engine arrangement with the water cooled manifolds. (G) Install the cup plugs in the rear side of each cylinder head to the following distance. ... 4.3 0.8 mm (0.17 0.03 inch)


Back to top