3H9-06133-0 Tohatsu PROTECTOR, WIRE HARNESS

Table 1
Quantity    Part Number    Part Name    Function    
1     4C-5719     Piston Ring Compressor     The compressor is used for compressing piston rings into ring grooves prior to installation of the piston. (1)    
1     4C-6594     Timing and Fuel Setting Tool     The tool is used for testing and adjusting of injector synchronization. The fuel timing dimension can also be measured and adjusted with this tool.    
1     4C-6173     Fuel Drain Tray     The tray is used for draining fuel filters.    
1     4C-9041     Cylinder Installation Tool     This tool provides a method of attaching a hoist for removal and installation of the cylinder assembly, cylinder liner, piston and connecting rod assembly.    
1     6D-7726     Hose As     The hydraulic hose is
384 cm (151 inch) long. The connections have 1/4-18 NPTF threads.    
3     3J-5390     Plug     The 3/8-18 NPTF pipe plugs are used with the 8T-5206 Manifold.    
3     1P-2375     Quick Connect Coupler     The male coupler is used with all Caterpillar hydraulic service tools.    
4     1P-2376     Quick Connect Coupler     The female coupler is used with all Caterpillar hydraulic service tools.    
1     2P-5534     Thread Tap     The 1/2 inch NPTF thread tap is used for cleaning internal threads for the manual valves.    
1     5P-4773     Torque Wrench Adapter     The adapter has a 1/2 inch drive and a 5/8 inch box end with 12 points.    
1     8T-0890     Puller Group     The puller is used for removing the rotor covers from centrifugal oil filters.    
2     8T-0914     Guide Pin     The pins are used for alignment and support of the flywheel and the support assembly for the rear gear during removal and installation. The pins are also used for removal and installation of the vibration damper.    
1     8T-2681     Main Bearing Driver     The driver is for help in the removal and installation of the main bearings.    
1     8T-3029     Camshaft Support     The support holds camshaft segments during removal and installation.    
1     8T-3033     Piston Ring Expander     The expander is used for removal and installation of piston rings.    
2     8T-3268     Unit Injector Removal Bolt     The bolts are for removing the injectors.    
1     8T-5206     Manifold     The hydraulic manifold has six ports with 3/8-18 NPTF threads.    
1     1U-6396     O-Ring Assembly Compound     The compound holds O-rings in place during assembly procedures.    
1     1U-7544     Hydraulic Hand Pump     The manual pump is for use with hydraulic tools.    
1     1U-9824     Oil Drain Tool Group     This tool group is used for servicing the oil filters.    
1     9U-7522     Cylinder Head Repair Tool     The tools in this set are used for removal, inspection, and installation of cylinder head components.    
1     6V-4876     Lubricant     The lubricant is a molybdenum paste that helps to prevent galling on the threads of cylinder head bolts.    
1     6V-6080     Torque Multiplier Gp     The torque multiplier is used to provide torque that is greater than the capacity of torque wrench.    
1     6V-7073     Cylinder Liner Puller     The puller is for removal and installation of the cylinder liners. (2)    
1     126-6918     Lifting Bracket     The bracket is used for removing and installing the cylinder head assembly. The bracket requires two 5D-1972 Bolts and one 126-6920 Handle Rod.    
1     130-6993     Injector Seat Cleaning Brush     The brush is used to clean the seats for the injectors.    
1     134-0932     Main Bearing Driver     The driver is used for the removal and installation of crankshaft main bearings.    
1     136-1452     Internal Tip Pliers     The pliers are used for removal and installation of piston pin ring retainers and/or snap rings.    
1     138-7573     Link Bracket     The brackets are lifting aids that are used for removal and installation of various components.    
1     138-7575     Link Bracket    
4     153-8487     Stud Tensioner Tool Gp (Cylinder Head)     The stud tensioners are used for removal and installation of cylinder heads.    
2     153-8488     Stud Tensioner Tool Gp (Crankshaft Main Bearing)     The stud tensioners are used for removal and installation of main bearing caps.    
1     156-7155     Camshaft Bearing Tool