9208E3-0620 Tohatsu SCREW


9208E3-0620 SCREW Tohatsu MFS25B, MFS25B, MFS30B SCREW
9208E3-0620 SCREW Tohatsu
Rating:
78

Buy SCREW 9208E3-0620 Tohatsu genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Compatible models:

MFS25B   MFS30B   Tohatsu

Tohatsu entire parts catalog list:

MFS25B 2010
MFS25B 2011,2012,2013,2014
MFS30B 2010

Information:


Table 1
J1939 Code and Description Comments
110-17
Engine Coolant Temperature : Low - least severe (1) The engine coolant temperature is below the trip point temperature for the programmed delay time.
The code is logged. Probable Causes
Codes
Light loads
Jacket water heater
Sensor
Connectors and wiring
Temperature regulatorsRecommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect the Cat® Electronic Technician (Cat ET) Service Tool to the service tool connector.
B. Look for active codes that are associated with the system for the event code.
Codes
Result: An associated code is active.
Repair: Troubleshoot any associated codes before continuing with this test.
Result: A code is active or logged.
Proceed to Test Step 2.
2. Check for Light Loads
A. Consult the operator to determine the usual load factor.
Load
Result: The load factor is OK.
Proceed to Test Step 3.
Result: The load factor is less than 50 percent.
Note: This overcooling is caused by the reduced amount of heat that is produced by the engine during light loads.
Repair: Operate the engine at a load that is greater than 50 percent.
If the problem is not resolved, proceed to Test Step 3.
3. Check for Proper Operation of the Jacket Water Heater
Heater
Result: The jacket water heaters are OK.
Proceed to Test Step 4.
Result: The jacket water heaters are NOT OK.
Repair: Repair or replace damaged jacket water heater.
If the problem is not resolved, proceed to Test Step 4.
4. Check the Coolant Temperature Sensor
Note: The sensor may be indicating an incorrect temperature that is within the normal range of the sensor.
A. Connect Cat ET.
B. Use Cat ET to monitor the following temperature:
- Coolant temperature
Note: The temperature should rise steadily as the engine is warmed.
C. Ensure that the temperature is reasonable.
D. Reference the reading to another temperature indicator when possible. Refer to Testing and Adjusting, "Cooling System" for additional information.
Sensor
Result: The temperature sensor is OK.
Proceed to Test Step 6.
Result: The temperature sensor is NOT OK.
Proceed to Test Step 5.
5. Inspect the Electrical Connectors and the Wiring
A. Turn the main disconnect switch to the OFF position.
B. Thoroughly inspect the connectors. Refer to Troubleshooting, "Electrical Connectors-Inspect" for additional information.
C. Perform a 45 N (10 lb) pull test on the connector wires.
D. Check the harness for abrasions and pinch points.
Connectors and Wiring
Result: The connectors and wiring appear to be OK.
Repair: Replace the sensor.
If the problem is not resolved, proceed to Test Step 6.
Result: There is a problem with the connectors and/or wiring.
Repair: Repair or replace the connectors or wiring. Ensure that all the seals are properly in place and ensure that the connectors are coupled.
If the problem is not resolved, proceed to Test Step 6.
6. Check the Water Temperature Regulators
Note: The water temperature regulators should not begin to open until jacket water reaches opening temperature for the regulators.
A. Allow the engine to cool and then start the engine. Check the hose at the outlet for the jacket water. If the hose is warm and normal operating temperature is not achieved yet, a regulator may be stuck open.
B. If the water temperature regulators are malfunctioning, check the water temperature regulators. Refer to Testing and Adjusting, "Cooling System" for additional information.
Regulators
Result: The temperature regulators are NOT OK.
Repair: Replace the water temperature regulators.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts screw Tohatsu:

910103-0612
SCREW, MOTOR COVER
910103-0612 SCREW, MOTOR COVER
M115A2, M15D2, M18E2, M2.5A, M25C3, M30A4, M40C, M40D2, M40D2, M40D2, M50D2, M9.9D2, MD115A, MD115A2, MD40B2, MD40B2, MD50A, MD50B2, MD50B2, MFS2.5B, MFS2.5B, MFS2.5B, MFS25A, MFS25B, MFS25B, MFS25B, MFS2B, MFS3.5B, MFS3.5B, MFS3.5B, MFS30A, MFS30B,
921521-6408
 
921521-6408 SCREW
M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD50B2, MD50B2, MFS15B2, MFS15B2, MFS15C, MFS15C, MFS18B2, MFS18B2, MFS20C, MFS20C, MFS25A, MFS25B, MFS25B, MFS25B, MFS30A,
921503-0510
SCREW
921503-0510 SCREW
M4C, M5B, M5BS, M8B, M9.8B, MD115A2, MD40B2, MD40B2, MD50B2, MD50B2, MD70B, MD75C2, MD90B, MD90C2, MFS15C, MFS20C, MFS25B, MFS25B, MFS30B, MFS4A2, MFS4B, MFS4C, MFS5A2, MFS5B, MFS5C, MFS6A2, MFS6B, MFS6C, MFS8A, MFS8A3, MFS8A3, MFS8A3, MFS9.8A, MFS9.
921503-6410
 
921503-6410 SCREW
M4C, M5B, MFS25B, MFS25B, MFS30B
3R0-07238-0
 
3R0-07238-0 SCREW
MFS15B2, MFS15B2, MFS15C, MFS15C, MFS18B2, MFS18B2, MFS20C, MFS20C, MFS25A, MFS25B, MFS25B, MFS25B, MFS30A, MFS30B, MFS30B, MFS8A, MFS8A2, MFS8A3, MFS8A3, MFS8A3, MFS8A3, MFS9.8A, MFS9.8A2, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.9B2, MFS9.9B2,
9215E3-0612
 
9215E3-0612 SCREW
MFS15C, MFS15C, MFS20C, MFS20C, MFS25B, MFS25B, MFS30B, MFS4B, MFS4C, MFS5B, MFS5C, MFS6B, MFS6C, MFS8A3, MFS8A3, MFS8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.9C
921503-6416
 
921503-6416 SCREW
MFS25B, MFS25B, MFS30B
3AC-03234-0
 
3AC-03234-0 SCREW
MFS25B, MFS25B, MFS30B
Back to top