9401E3-1000 Tohatsu WASHER


9401E3-1000 WASHER Tohatsu MD115A2, MD40B2, MD40B2, MD50B2, MD50B2, MFS15C, MFS15C, MFS20C, MFS20C, MFS25B, MFS25B, MFS30B, MFS8A3, MFS8A3, MFS8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.9C WASHER
9401E3-1000 WASHER Tohatsu
Rating:
103

Buy WASHER 9401E3-1000 Tohatsu genuine, new aftermarket parts with delivery
Number on catalog scheme: 35
 

Tohatsu entire parts catalog list:

MD115A2 2010,2012,2013,2014
MD40B2 2010
MD40B2 2011,2012,2013,2014
MD50B2 2010
MD50B2 2011,2012,2013,2014
MFS15C 2008,2009,2011,2012,2013,2014
MFS15C 2010
MFS20C 2008,2009,2011,2012,2013,2014
MFS20C 2010
MFS25B 2010
MFS25B 2011,2012,2013,2014
MFS30B 2010
MFS8A3 2007,2008,2009
MFS8A3 2010
MFS8A3 2011,2012,2013,2014
MFS9.8A3 2007,2008,2009
MFS9.8A3 2010
MFS9.8A3 2011,2012,2013,2014
MFS9.9C 2008,2011

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
B(1) 304-6597 Adapter 1
B(2) 268-1969 Adapter 1
B(3) 9U-6194 Adapter 1
(1) C0.5 and C0.7 engines
(2) C1.1 and C1.6 engines
(3) C1.5 and C2.2 enginesStart By:
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install suitable plugs to the inlet ports of the cylinder head in order to prevent the entry of loose parts into the engine.
Plug the apertures for the push rods in the cylinder head in order to prevent the entry of loose parts into the engine.
Note: The removal procedure is similar for the two cylinder, the three cylinder and the four cylinder engines. The following procedure should be adopted in order to remove the valve springs when the cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head that has been removed from the engine.Note: Ensure that the appropriate piston is at the top center position before the valve spring is removed. Failure to ensure that the piston is at the top center position may allow the valve to drop into the cylinder bore.
Illustration 1 g01304583
Typical example
Follow Steps 1.a through 1.d in order to position the appropriate piston at top center.
Install Tooling (A) and (B) in position on the cylinder head in order to compress a valve spring for the appropriate piston.
Use Tooling (A) in order to compress valve spring (3) and open the valve slightly. Note: Do not compress the spring so that the valve spring retainer (2) touches the valve stem seal.
Carefully rotate the crankshaft until the piston touches the valve. Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent valve stems.
Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the piston is at the top center position. The valve is now held in a position that allows the valve spring to be safely removed.
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Use tool (A) in order to compress valve spring (3). Remove valve keepers (1). Note: For four cylinder engines, if all valve springs require replacement the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before changing from one pair of cylinders to another pair of cylinders.
Do not turn the crankshaft while the valve springs are removed.
Apply sufficient pressure to Tooling (A) in order to allow removal of the valve keepers (1). Note: Do not compress the spring so that the valve spring retainer (2) touches the valve stem seal.Remove valve keepers (1).
Slowly release the pressure on Tooling (A).
Remove valve spring retainer (2) and remove valve spring (3).
Remove Tooling (A) and (B). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
B(1) 304-6597 Adapter 1
B(2) 268-1969 Adapter 1
B


Parts washer Tohatsu:

941303-0600
WASHER
941303-0600 WASHER
M115A2, M120A2, M140A2, M15D2, M18E2, M2.5A, M2.5A2, M25C3, M3.5A2, M3.5B2, M30A4, M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, M8B, M9.8B, M9.9D2, MD115A, MD115A2, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD5
3C8-66308-0
WASHER, 6 - 16 - 1.5
3C8-66308-0 WASHER, 6 - 16 - 1.5
M115A2, M120A2, M140A2, M15D2, M18E2, M2.5A, M2.5A2, M25C3, M3.5A2, M3.5B2, M30A4, M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, M8B, M9.8B, M9.9D2, MD115A, MD115A2, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD5
940103-0600
WASHER
940103-0600 WASHER
M115A2, M120A2, M140A2, M15D2, M18E2, M2.5A, M2.5A2, M25C3, M3.5A2, M3.5B2, M30A4, M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, M8B, M9.8B, M9.9D2, MD115A, MD115A2, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD5
940113-0600
WASHER
940113-0600 WASHER
M115A2, M120A2, M140A2, M15D2, M18E2, M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, M9.9D2, MD115A, MD40A, MD40B, MD40B, MD50A, MD50B, MD50B, MD50B, MD70B, MD70B, MD70B, MD90B, MD90B, MD90B, MFS15B2, MFS15B2, MFS18B2, MFS18B2, MFS2.5A
940103-0800
WASHER
940103-0800 WASHER
M115A2, M120A2, M140A2, M15D2, M18E2, M25C3, M30A4, M40C, M40D2, M40D2, M40D2, M4C, M50D2, M5B, M5BS, M60C, M70C, M8B, M9.8B, M9.9D2, MD115A, MD115A2, MD40A, MD40B, MD40B, MD40B2, MD40B2, MD50A, MD50B, MD50B, MD50B, MD50B2, MD50B2, MD70B, MD70B, MD70
3R3-07406-0
WASHER, 14.5 - 24 - 1
3R3-07406-0 WASHER, 14.5 - 24 - 1
MFS15B2, MFS15B2, MFS15C, MFS15C, MFS18B2, MFS18B2, MFS20C, MFS20C, MFS25A, MFS25B, MFS25B, MFS25B, MFS30A, MFS30B, MFS30B, MFS8A, MFS8A2, MFS8A3, MFS8A3, MFS8A3, MFS8A3, MFS9.8A, MFS9.8A2, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.9B2, MFS9.9B2,
3P0-66233-0
WASHER, 8.1 - 16 - 1.5
3P0-66233-0 WASHER, 8.1 - 16 - 1.5
M15D2, M18E2, M25C3, M30A4, M40C, M9.9D2, MFS15B2, MFS15B2, MFS15C, MFS15C, MFS18B2, MFS18B2, MFS20C, MFS20C, MFS25A, MFS25B, MFS25B, MFS25B, MFS30A, MFS30B, MFS30B, MFS8A3, MFS8A3, MFS8A3, MFS9.8A3, MFS9.8A3, MFS9.8A3, MFS9.9B2, MFS9.9B2, MFS9.9C
346-64124-5
WASHER, 12.5 - 32 - 2.5
346-64124-5 WASHER, 12.5 - 32 - 2.5
M15D2, M18E2, M25C3, M30A4, M9.9D2, MFS15B2, MFS15B2, MFS15C, MFS15C, MFS18B2, MFS18B2, MFS20C, MFS20C, MFS25A, MFS25B, MFS25B, MFS25B, MFS30A, MFS30B, MFS30B, MFS9.9B2, MFS9.9B2, MFS9.9C
Back to top