22448834 Volvo.Penta Adapter

Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     8T-3029     Camshaft Support     1    
1U-6311 Plate     1    
B     1P-2382 (1)     Wrench Adapter     1    
9U-5932 (1) Torque Wrench Extension     1    
C     6V-6080     Torque Multiplier Gp     1    
5P-1748 Socket     1    
D     4C-5593     Anti-Seize Compound     -    
E     8T-5096     Dial Indicator Gp     1    
( 1 ) Only one tool is required. Be sure that the proper tool is used for your engine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.The correct relationship of the camshaft segments must be observed at the time of assembly. If the camshaft segments are not properly timed, serious engine damage will occur.
Illustration 1 g01311484
This Illustration shows the location of the dowels on the camshaft bearing journal. (X) Location of the single dowel in the face of the camshaft bearing journal (Y) Location of the variable dowel in the face of the camshaft bearing journal (Z) Locating groove
Illustration 2 g01301748
This Illustration shows the location of the dowels on the camshaft bearing journal. (X) Location of the single dowel in the face of the camshaft bearing journal (Y) Location of the variable dowel in the face of the camshaft bearing journal (Z) Locating grooveNote: The position of the single dowel in relation to the variable dowel determines the letter designation of the cam journals. The single dowel is located on the same end as the locating groove. The variable dowel is located on the end that is opposite of the locating groove.
Illustration 3 g01301753
This Illustration shows the letter designation of 3608 camshaft journals.
Before assembly, check the location of the dowel and the height of each camshaft journal. Refer to Specifications, "Camshaft" for the assembled height of each dowel.Note: Install the camshaft journals with the locating groove toward the front of the engine for both standard rotation engines and reverse rotation engines.Install the camshaft segments in the orientation that was noted during removal.Note: Engine rotation is observed from the flywheel end of the engine.
Illustration 4 g01425662
Apply clean engine oil to the rear camshaft bearing.
Use two people in order to install shaft assembly (19) . The weight of shaft assembly (19) is approximately 27 kg (59 lb). Put the spacer in position on shaft assembly (19) . Align the dowel in the shaft assembly with the dowel hole in the camshaft segment. Install shaft assembly (19) .
Install plate (18) and bolts (17) on shaft assembly (19) .
Install governor drive gear (16) and bolts (15) on shaft assembly (19) .
Illustration 5 g01425667
Move the camshaft to the rear against the plate.
Put shims (13) in position on pinion assembly (11) . Install new O-ring seals (14) . Apply clean engine oil to the O-ring seals.
Put pinion assembly (11) in position in rear housing (10) . Install the bolts that hold pinion assembly (11) .Note: Be sure that the camshaft is all the way to the rear against the plate assembly when you check the backlash between the gears. Also, be sure that the pinion is forced upward against the plate assembly when you check the backlash between the gears. When you set the backlash, be sure that the camshaft is not placed in a forward position. There will not be enough clearance between the gears when the camshaft moves rearward.
Use Tooling (E) to check the backlash between the pinion gear and the governor drive gear. As needed, add shims or remove shims (13) in order to obtain a backlash of 0.25 0.05 mm (0.010 0.002 inch).
Install coupling (12) .
Illustration 6 g00575676
Put the spacer in position on camshaft journal (2) .
Appl