244367 Volvo.Penta Adjusting washer


244367 Adjusting washer Volvo.Penta AQD70D; TAMD70D; TAMD70E, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B, TAMD60C, TD120C, TD60A; TD60B; TD60B PP, TD70G; TD70G-83; TD70GPP, TID120FPP; TID120FG; TD120G Adjusting
244367 Adjusting washer Volvo Penta
Rating:
33

Buy Adjusting washer 244367 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 26
 

Volvo Penta entire parts catalog list:

AQD70D; TAMD70D; TAMD70E
D42A; D42A PP
D70B; D70B PP; D70B K; TD70B
D70CHC; D70CRC; TD70CHC; TD70CRC
MD70B; MD70BK; TMD70B; THAMD70B; TAMD70B; AQD70BL; AQD70B
MD70C; TMD70C; TAMD70C; THAMD70C; AQD70BL; AQD70CL
TAMD60A; TAMD60B
TAMD60C
TD120C
TD60A; TD60B; TD60B PP; TD60B G
TD70G; TD70G-83; TD70GPP; TD70GPP-83; TID70G; TID70GPP; TID70GG; TD70GG; TD70GG-83
TID120FPP; TID120FG; TD120G; TD120GG PP; TD120GG

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     8T-5096     Dial Indicator Gp     1    
B     8T-9022     Silicone Gasket     -    
C     198-9113     Seal Installer     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00934767
Clean upper main bearing (4) and lubricate the bearing surface with clean engine oil.Note: Do not put oil on the back sides of the crankshaft main bearings.Note: Ensure that the upper halves of the main bearings are installed so that the bearing tabs fit into the notch in the cylinder block.
Only the upper half of the main bearing has lubrication holes. Make sure the upper half of the main bearing is installed correctly in the cylinder block to ensure proper lubrication.
Slide upper main bearing (4) into position between the crankshaft journal and the cylinder block.
Illustration 2 g00934803
Clean main bearing cap (2) and lower main bearing (3). Lubricate the bearing surface of lower main bearing (3) with clean engine oil.Note: Ensure that the lower halves of the main bearings are installed so that the bearing tabs fit into the notch in the main bearing caps.
Install lower main bearing (3) in main bearing cap (2) .
Illustration 3 g01358190
Install main bearing cap (2). Lubricate the threads of bolts (1) with clean engine oil. Install bolts (1) and tighten finger tight.
Repeat Steps 1 through 5 for the remaining main bearings.Note: Do not install the rear main bearing cap yet.
Illustration 4 g01001838
Install the upper half of thrust washer (6) on the rear of the cylinder block with the Oil Grooves (X) toward the outside. If necessary, move the crankshaft to the front or to the rear in order to install the thrust washer.
Illustration 5 g00934744
Install the lower half of thrust washer (5) on each side of the rear main bearing cap. The grooves on the thrust washer must be located against the crankshaft.
Illustration 6 g01041142
Apply Tooling (B) to the corners of the rear main bearing cap. Install the rear main bearing cap to the cylinder block so that the rear face is even with the rear face of the cylinder block.
Illustration 7 g01033394
Apply soapy water to side seals (7). Position side seals (7) in the grooves on the rear main bearing cap with the rounded edges of the seals toward the outside. Use Tooling (C) to push the seal into position in order to reduce the risk of damaging the seal's metal core. Apply Tooling (B) around side seals (7) .
Install the bolts for the rear main bearing cap. Tighten all of the bolts for the main bearing caps to a torque of 98 to 108 N m (72 to 80 lb ft).
Rotate the crankshaft in order to ensure that the crankshaft turns freely.
Check the crankshaft end play. Use a prybar to move the crankshaft toward the front of the engine. Use Tooling (A) to measure the end play. The maximum permissible crankshaft end play is 0.300 mm (0.0118 inch).End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".


Parts adjusting Volvo Penta:

846959
Adjusting washer
846959 Adjusting washer
2001; 2001B; 2001AG, AQD70D; TAMD70D; TAMD70E, DH10A; DH10A 285; DH10A 360, MD11; MD11C; MD11D, MD120A; MD120AK; TMD120A, MD70C; TMD70C; TAMD70C, TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TA
860174
 
860174 Adjusting washer
2001; 2001B; 2001AG, D70CHC; D70CRC; TD70CHC, TAD1030G; TD1010G; TWD1010G, TAD1230P; TD121GP-87; TWD1210P, TAMD122A; TMD122A; TAMD122P-A, TAMD71A; TAMD72A, TAMD71B; TAMD73P-A; TAMD73WJ-A, TAMD72P-A; TAMD72WJ-A, TD100CHC; TD100CRC; TD121CHC, TD100G-87
233994
 
233994 Adjusting washer
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAD1230P; TD121GP-87; TWD1210P, TAMD60A; TAMD60B, TAMD60C,
241734
 
241734 Adjusting washer
D100A; D100AK; D100B, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, MD11; MD11C; MD11D, MD1B; MD2B; AQD2B, MD5A; MD5B; MD5C, MD70B; MD70BK; TMD70B
846950
 
846950 Adjusting washer
MD11; MD11C; MD11D, TAMD60A; TAMD60B, TD60A; TD60B; TD60B PP
846529
 
846529 Adjusting plate
D100A; D100AK; D100B, D120A; D120AK; TD120A, MD120A; MD120AK; TMD120A, TAD1030P, TAD1230P; TD121GP-87; TWD1210P, TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAD1641VE; TAD1642VE; TAD1643VE, TAD940GE; TAD941GE, TAD940VE; TAD941VE; TAD942VE, TAM
78429
 
78429 Adjusting washer
D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B
870263
 
870263 Adjusting washer
D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P, TAMD60A; TAMD60B, TD120C, TD164KA
Back to top