941830 Volvo.Penta Adjusting washer

Illustration 1 g02295833
Typical example
Illustration 2 g02295755
Typical example
Table 1
Specifications for 355-1060 Exhaust Cooler and Mounting Gp (NRS)    
Callout     Part Number     Part Name     Specification Description    
1     375-0351     Bolt     Torque to...................
22 N m (16 lb ft)    
2     6I-0260     Bolt     Torque to...................
18 N m (13 lb ft)    
3     6I-0260     Bolt     Torque to...................
22 N m (16 lb ft)    
4     6I-0254     Bolt     Torque to...................
18 N m (13 lb ft)    
5     100-4830     Bolt     Torque to...................
44 N m (32 lb ft)    
6     6I-0260     Bolt     Torque to...................
22 N m (16 lb ft)    
7     6I-0260     Bolt     Torque to...................
18 N m (13 lb ft)    
8     6I-4045     Bolt     Torque to...................
44 N m (32 lb ft)    
9     6I-0260     Bolt     Torque to...................
18 N m (13 lb ft)    Removal Procedure
Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Note: Plug or cap all open ports with new plugs or caps.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Remove the exhaust back pressure valve. Refer to Disassembly and Assembly, "Exhaust Back Pressure Valve" for the correct procedure.
Illustration 3 g02413837
Loosen hose clamp (13) and remove hose assembly (12) from the turbocharger.
Remove bolts (6) and bolts (11). Remove tube assembly (5) from NRS exhaust cooler (17) .
Remove gasket (7) (not shown) and gasket (16) (not shown) from tube assembly (5) .
Remove bolt (2) from the clip for the tube assembly.
Loosen bolts (1) for the support bracket.
Remove bolts (4) and bolts (9). Remove tube assembly (8) from the NRS exhaust cooler.
Remove gasket (3) (not shown) and gasket (10) (not shown) from tube assembly (8) .
Illustration 4 g02413956
Illustration 5 g02413916
Cut cable strap (22) .Note: Note the position of the cable strap and the type of cable strap installed.
Remove bolts (18) and bolts (20) from tube assembly (21). Remove the tube assembly from the NRS exhaust cooler.
Remove gasket (23) (not shown) and gasket (19) (not shown).
Apply releasing fluid prior to and during the removal of bolts (25). Remove bolts (25) .
Apply releasing fluid prior to and during the removal of bolts (26). Remove bolts (26) .
Remove tube assembly (28) from the NRS exhaust cooler.
Remove gasket (24) (not shown) and gasket (27) (not shown) from tube assembly (28) .
Remove the turbocharger. Refer to Disassembly and Assembly, "Exhaust Manifold and Turbocharger" for the correct procedure.
Illustration 6 g02415777