463505 Volvo.Penta Air filter insert


463505 Air filter insert Volvo.Penta AD30A; AQAD30A; MD30A, MD40A; TMD40A; TMD40B Air
463505 Air filter insert Volvo Penta
Rating:
98

Buy Air filter insert 463505 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$30.00

14-03-2025

CN: ETCAUTO Martine
HeuroFosh 876185 Air Filter for Voolvo Penta Diesel Engine AQ30 AD30 MD30 MD40 KAD42A KAMD42A 463505 18-7890
Heurofosh This is a Air Filter Insert for Volvo Penta Diesel Engines || Replaces Volvo Penta 463505 876129 863344 842680 and Sierra 18-7890 || Fit for Volvo Penta AD30A AQAD30A MD30A MD40A TMD40A TMD40B MD30 40 KAD42 KAD32 TAMD61 TAMD71 KAD32P TAMD42WJ-A KAD43P-A KAD42A KAMD42A HS1A KAD42B KAMD42B TAMD42B KAD42P-A KAMD42P-A HS1A TAMD61A TAMD62A TAMD71A TAMD72A TAMD71B TAMD73P-A TAMD73WJ-A TAMD72P-A TAMD72WJ-A || Effective Filtration: The insert helps to keep dirt and debris out of the engine, ensuring optimal performance and longevity || Easy Installation: Designed for straightforward replacement, making it easy for users to maintain their engines without specialized tool
$25.99

25-12-2024

US: PremiumpartsWhosale
A-Premium 2-PC Engine Air Filter Compatible with Volvo 240 1990-1993, 242 1975-1984, 244 1975-1989, 245 1976-1989, 264 1980-1981, 2.0L 2.1L 2.3L
A-Premium [Vehicle Fitment]: Compatible with Volvo 240 1990 L4 2.3L, 240 1991 L4 2.3L (Standard; Manual Transmission), 240 1992-1993 L4 2.3L, 242 1975 L4 2.0L, 242 1984 L4 2.1L, 242 1976-1981 L4 2.1L, 242 1981-1984 L4 2.3L, 242 1982-1983 L4 2.1L (Naturally Aspirated), 244 1981-1989 L4 2.3L, 244 1982-1984 L4 2.1L (Naturally Aspirated), 264 1980-1981 L4 2.1L --- Flexible Panel Air Filter || [Reference Number]: CA4365, PA3436, A814C, 46111, 463505 || [Specifications]: ① Location: Front; ② Length: 13.15 inch; ③ Width: 6.46 inch; ④ Height: 1.46 inch; ⑤ Shape: Rectangular; ⑥ Washable: No; ⑦ Reusable: No; ⑧ Package Quantity: 1; ⑨ Packaging Type: Box || [Enhanced Performance]: A-Premium Engine Air Filter uses fine filtration media to capture all kinds of debris without obstructing airflow, removing dangerous particles, improving engine performance and increasing engine efficiency. || [Replacement Suggestion]: To ensure that the engine air filter provides your engine with clean air, recommended replacement every 12 months, 12,000 miles or as specified by the vehicle manufacturer.
$57.10

25-12-2024
0.1102[0.05] pounds
CN: GaoMo
[Renewal Part] 876185 Air Filter Insert for Volvo Penta for Diesel Engines AQ AD MD 30 TMD40 KAD42 TAMD 71 72 73 463505 For KAD42-44 [Replacement]
LFCBMD 100% brand new and high quality. || Made of high quality material, durable and practical to use. || Delicate and exquisite, highly match the equipment. || Solid and durable, long service life. || Easy to install and reliable to use. || Ensure practicality and durability
Number on catalog scheme: 2
 

Compatible models:

Information:

Remove Governor
1. Move the governor control to the "OFF" position. 2. Disconnect spring (4) from the lever on the governor. Disconnect rod (3) from the lever on the governor.3. Disconnect tube (2) from the fuel ratio control.4. Remove six bolts (5) that hold the governor to the fuel pump and governor drive housing. Remove governor (1).Install Governor
1. Put governor (1) in position on the fuel pump and governor drive housing.
Make sure lever (2) engages in the rack assembly.
2. Install the six bolts (5) that hold the governor in position.3. Connect rod (4) and spring (6) to the lever on the governor.4. Connect tube (3) to the fuel ratio control.5. Install tool (A) as shown. Move the governor control to the "ON" and "OFF" positions. If the indicator from tool (A) moves in both directions the lever in the governor is engaged in the correct position in the rack assembly. If the indicator moves in one direction only, remove the governor and check the position of the lever in the rack assembly.Disassemble Governor
start by: a) remove fuel ratio controlb) remove governor 1. Remove bolt (2). Remove cover (1) and the gasket from over the high and low idle screws. 2. Remove five bolts (3) from the cover. Loosen the high and low idle screws. Remove cover (4) and the gasket from the housing assembly. 3. Remove high idle screw (6) and low idle screw (5) from the cover.4. Remove the seal from the high idle screw. 5. Remove pin (7) from the low idle screw. 6. Install tool (A) on the end of the low idle screw as shown. Put the low idle screw in a vise and use pry bars to remove end (8) from sleeve (9). 7. Remove screw (10) from the sleeve. Remove spring (11) from the end. Remove seal (12) from the end. 8. Loosen screw (16). Remove collar (13) and spring (14) from the bolt.9. Loosen bolt and nut (15). Remove lever (17) from the shaft. 10. Remove plug (18), spring (19) and plunger (20) from the housing assembly. 11. Remove two bolts (21) and the lock from the torque control. Remove torque control (22) from the housing assembly. 12. Remove four bolts (23). Remove housing assembly (24) from the lower housing assembly. 13. Remove seat assembly (28), wave washer (25), washer (27), wave washer (26) and spring (25) from the guide in the housing assembly. 14. Remove bolt (29) and the lock from the shaft and band assembly. 15. Remove shaft (30) and the lever assembly from the housing assembly. 16. Remove pin (31) from the lever assembly. Remove spring (33) and plunger (32). 17. Remove seal (34) from the housing assembly. 18. Remove plug (35) from the housing assembly. 19. Remove two bearings (36) from the housing assembly. 20. Remove bumper spring (39) from the bolt.21. Remove bolts (38) and lock (40) that hold the weight assembly in position. Remove weight assembly (37). 22. Remove ring (43) and pin (44) from the seat.23. Remove seat (42) and bolt (41). 24. Remove two washers (45) and spring (46) from the seat. 25. Remove sleeve (47), two races (48), bearing (50) and ring (49) from the weight assembly. 26. Remove valve (51) from the weight assembly. 27. Remove ring (54). Remove cylinder (53) from weight assembly (52).28. Remove the two pins that hold the weights in position. Remove the weights. 29. Remove sleeve (55) and piston (56) from the cylinder. 30. Remove seal (57) from the piston. 31. Remove valve assembly (58) and the gasket from the housing assembly. 32. Remove pin (61), slug (60) and spring (59) from the valve assembly. 33. Remove shaft (62) from the housing assembly. 34. Remove seal (63) from the shaft. 35. Remove pin (64) from the housing assembly. 36. Remove cover (65) and shaft assembly (66) from the housing assembly.37. Remove gear (67) from the cover. 38. Remove ring (69) from the groove in the retainer.39. Remove dowel (72) from the retainer, gear assembly and shaft assembly. Remove the shaft assembly and gear assembly from the cover.40. Remove the pin that holds yoke (71) to the spring. Remove the yoke.41. Remove the pin that holds the spring to the gear. Remove retainer (68) and spring (70) from the gear. 42. Remove gear (73) from the shaft assembly with an arbor press. 43. Remove bearing (74) from the housing assembly.Assemble Governor
1. Install plunger (2), and spring (1) in the lever assembly. Install pin (4) that holds the plunger and spring in position. 2. Install the two bearings in the housing part of the way with tool (A). 3. Put lever assembly (3) in the housing assembly as shown. Install the shaft.4. Measure the distance between the guide and the lever assembly with a feeler gauge as shown.5. Dimensions (X) and (Y) are controlled by the depth of the two bearings in the housing assembly. Dimension (Y) must be .1227 .004 in. (3.12 0.1 mm). Dimension (X) must be .0877 .004 in. (2.2 0.1 mm). It might be necessary to remove the shaft and lever assembly in order to find a location for the bearings so dimensions (X) and (Y) are correct.6. Remove the shaft and lever assembly from the housing assembly. 7. Install the seal in the housing assembly with tool (B). Install the seal even with the outside surface of the housing assembly and with the lip toward the inside of the housing assembly. 8. Install the lever assembly and shaft in the housing assembly. Install the lock and bolt (5) that hold them. 9. Install plug (6) in the housing assembly with tool (C). 10. Put shaft assembly (7) in gear (8) as shown. Push the shaft assembly on the gear with


Parts air Volvo Penta:

7744060_045
Back to top