7744650_019 Volvo.Penta alternator and installation comps

Introduction
This Special Instruction covers the field installation of the Engine Idle Shutdown (EIS) on certain Medium Wheel Loader machines.Do not perform any procedure or order parts that are outlined in this publication until you understand the information that is contained in this document.Operation of the EIS on A Medium Wheel Loader Machine
This function shuts down the engine after the operator has not operated the machine for a certain time. This function does not shut down other systems, such as AC, which can run down the battery after idle shutdown. This function can be enabled or disabled by a Caterpillar dealer technician. Engine Idle Shutdown may be required for local regulations.The Engine Idle Shutdown (EIS) shuts down the engine after a delay time if the following conditions are met:
Engine coolant temperature must be warm since the last start.
The parking brake is applied.
The left service brake is released.
The throttle pedal is released.
Gear is in neutral.
The implement is not active.
Engine Idle Shut down - 20 seconds before the engine shuts down the action lamp will light and an alarm will sound. In order to cancel the shutdown, an operator can activate any of the controls above. The recommended option is the use of the left brake pedal in order to cancel a shutdown.Note: All the OMMs have been updated to contain this same operation information.Field Installation of EIS
Engine software, transmission control software and monitor software need updated and configured in order to install EIS. Use ET2009C or higher for installation and the configuration. A film will also be applied within the cab for the EIS.Update the Engine Software
Table 1
Model    Part Number    Description    
950H (1)     353-2728     Engine Ratings Electronic Software Gp    
353-2730 Engine Ratings Electronic Software Gp    
950H Japan Only     353-2729     Engine Ratings Electronic Software Gp    
962H & IT62H     353-2730     Engine Ratings Electronic Software Gp    
962H & IT62H Japan Only     353-2731     Engine Ratings Electronic Software Gp    
966H     353-2732     Engine Ratings Electronic Software Gp    
966H Japan Only     353-2733     Engine Ratings Electronic Software Gp    
972H     353-2734     Engine Ratings Electronic Software Gp    
972H Japan Only     353-2735     Engine Ratings Electronic Software Gp    
980H (2)     353-2737     Engine Ratings Electronic Software Gp    
980H (3)     353-2736     Engine Ratings Electronic Software Gp    
980H (2) Japan Only     355-1031     Engine Ratings Electronic Software Gp    
( 1 ) Check SIS flash files for the particular serial number in order to determine the correct file.
( 2 ) The EIS can be installed on 980H machines that have a serial number of 1-3999.
( 3 ) The EIS can be installed on 980H machines that have a serial number of 4000 - Up or have been updated with the 318-8496 Engine Kit Update the Transmission Control Software
Table 2
Model    Part Number    Description    
950H     355-7175     Power Train Software Gp    
962H & IT62H    
966H    
972H    
980H     355-7177     Power Train Software Gp    Update the Monitor Software
Table 3
Model    Part Number    Description    
950H     352-3302     Monitor Software Gp    
962H     352-3304     Monitor Software Gp    
IT62H     355-2991     Monitor Software Gp    
966H     352-3306     Monitor Software Gp    
972H     352-3308     Monitor Software Gp    
980H     352-3310     Monitor Software Gp    Configuration
Use Caterpillar Electronic Technician (ET) in order to configure the following parameters in the transmission ECM:
Set the "Engine Idle Shutdown Installation Status" to "Installed".
Enter a factory password. Follow the instructions that are given in ET.
Use ET in order to configure the following parameters in the engine ECM:
Set "Engine Idle Shutdown Enable Status" to "Enabled"
Set the "Engine Idle Shutdown Delay Time" to the desired time before shutdown. Enter the time in minutes.
Illustration 1 g02128473
Place 352-9153 Film (Engine Idle Shut down) in the cab on the dashboard. Refer to Illustration 1.The following machines have "EIS" installed but not "Enabled" from the