847198 Volvo.Penta Anchorage


847198 Anchorage Volvo.Penta TD100G; TD100G-85; TD100G-87 Anchorage
847198 Anchorage Volvo Penta
Rating:
93

Buy Anchorage 847198 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$63.84
 

22-05-2023
0.3130[0.14] Pounds
-: -
New Mercury Mercruiser Quicksilver Oem Part # 847198 Pin-Actuator
Number on catalog scheme: 19
 

Compatible models:

Volvo Penta entire parts catalog list:

TD100G; TD100G-85; TD100G-87; TD100GG; TD100GG-85; TD100GG-87; TD100GGP-87; TD100HP-87; TD100HPB-87; TD100GP; TD100GP-85; TD100GGP; TID100K;

Information:


Illustration 1 g00295370
Bolt tightening sequence for the cylinder head
Use the following procedure in order to tighten the cylinder head bolts:
Put engine oil on the threads of the bolts and the nuts. Tighten bolts (1) through bolts (22) in a numerical sequence in Illustration 1. Torque for the bolts ... 110 N m (81 lb ft)
Tighten bolts (1) through bolts (22) again in a numerical sequence. Torque for bolts ... 110 N m (81 lb ft)
Rotate bolts (1) through bolts (22) in a numerical sequence to the following values:
Tighten the bolts of short length "S" to the following value. Rotate the bolts in a clockwise direction: ... 150 degrees
Tighten the bolts of medium length "M" to the following value. Rotate the bolts in a clockwise direction: ... 180 degrees
Tighten the bolts of long length "L" to the following value. Rotate the bolts in a clockwise direction: ... 210 degrees
Illustration 2 g00295371
Bolts, nuts, and components of the cylinder head
(1) Tighten the nuts that hold fuel injectors to the following torque: ... 12 N m (10 lb ft)Note: When the fuel injection nozzle is removed, the following items must be replaced: dust seal and seat washer. (2) Tighten the nuts for fuel line to the following torque: ... 18 N m (13 lb ft) (3) Tighten the bolts that hold the rocker shaft to the cylinder head to the following torque: Begin tightening the inner bolts. Then tighten the bolts by working toward the end of the shaft. Cast iron or steel bracket ... 75 N m (55 lb ft)Aluminum bracket ... 40 N m (30 lb ft) (4) Valve lash Inlet ... 0.20 mm (.008 inch)Exhaust ... 0.45 mm (.018 inch) (5) Maximum permissible nozzle projection below cylinder head face after resurfacing ... 4.45 mm (.175 inch)Maximum allowance for resurfacing ... 0.30 mm (.012 inch) (6) Depth of new cylinder head ... 102.79 to 103.59 mm (4.047 to 4.078 inch)Minimum depth of cylinder head after resurfacing ... 102.48 mm (4.035 inch)
Illustration 3 g00295372
Positions for measuring the bow of the cylinder head (typical example)
Maximum permissible amount of bow (curve of cylinder head) Naturally aspirated engines A ... 0.08 mm (.003 inch)B ... 0.15 mm (.006 inch)C ... 0.15 mm (.006 inch)Turbocharged engines A ... 0.13 mm (.005 inch)B ... 0.25 mm (.010 inch)C ... 0.25 mm (.010 inch)Tighten the bolts of the inlet manifold (not shown) to the following torque: ... 44 N m (32 lb ft)Tighten exhaust manifold nuts (not shown) to the following torque: Plated ... 44 N m (32 lb ft)Plain ... 50 N m (37 lb ft)Type 2 Engines and 7BJ Engines
Note: For a complete description of Type 1 and Type 2 engines, refer to the Specifications Module, "Engine Design" for more information.
Illustration 4 g00295370
Bolt tightening sequence for the cylinder head
Use the following procedure in order to tighten the cylinder head bolts:
Put engine oil on the threads of bolts. Tighten bolts (1) through bolts (22) in a numerical sequence in Illustration 4. Torque for bolts ... 110 N m (81 lb ft)
Tighten bolts (1) through bolts (22) again in a numerical sequence. Torque for bolts ... 110 N m (81 lb ft)
Rotate bolts (1) through bolts (26) in a numerical sequence to the following values:
Tighten the bolts of short length "S" to the following value. Rotate the bolts in a clockwise direction: ... 150 degrees
Tighten the bolts of medium length "M" to the following value. Rotate the bolts in a clockwise direction: ... 180 degrees
Tighten the bolts of long length "L" to the following value. Rotate the bolts in a clockwise direction: ... 210 degrees
Illustration 5 g00295373
Bolts, nuts, and components of the cylinder head
Note: When the fuel injection nozzle is removed, the following items must be replaced: dust seal and seat washer. (1) Tighten the bolts that hold the rocker shaft to the cylinder head to the following torques: Begin tightening the inner bolts. Then tighten the bolts by working toward the end of the shaft. Cast iron or steel bracket ... 75 N m (55 lb ft)Aluminum bracket ... 40 N m (30 lb ft) (2) Valve lash Inlet ... 0.20 mm (.008 inch)Exhaust ... 0.45 mm (.018 inch) (3) Maximum permissible nozzle projection below cylinder head face after resurfacing ... 4.45 mm (.175 inch)Maximum allowance for resurfacing ... 0.30 mm (.012 inch) (4) Depth of new cylinder head ... 102.79 to 103.59 mm (4.047 to 4.078 inch)Minimum depth of cylinder head after resurfacing ... 102.48 mm (4.035 inch)
Illustration 6 g00295372
Positions for measuring the bow of the cylinder head (typical example)
Maximum permissible amount of bow (curve of the cylinder head) A ... 0.08 mm (.003 inch)B ... 0.15 mm (.006 inch)C ... 0.15 mm (.006 inch)Tighten the bolts for the inlet manifold (not shown) to the following torque: ... 44 N m (32 lb ft)Tighten the nuts for the exhaust manifold (not shown) to the following torque: Plated ... 44 N m (32 lb ft)Plain ... 50 N m (37 lb ft)


Parts anchorage Volvo Penta:

821625
Anchorage
821625 Anchorage
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, TAD1030G; TD1010G; TWD1010G, TD100CHC; TD100CRC; TD12
837387
 
837387 Anchorage
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, TAD1030G; TD1010G; TWD1010G, TAMD122A; TMD122A; TAMD122P-A, TD100CHC; TD100CRC; TD121CHC, TD100G; TD100G-85; TD100G-87, TD120AHC; TD120ARC; TAD120AHC, TID120FPP; TID120FG; TD120
843643
Anchorage
843643 Anchorage
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, TD100CHC; TD100CRC; TD121CHC, TD100G; TD100G-85; TD100G-87, TMD102A; TAMD102A; TAMD102D
843642
 
843642 Anchorage
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, TD100CHC; TD100CRC; TD121CHC, TD100G; TD100G-85; TD100G-87, TMD102A; TAMD102A; TAMD102D
863425
 
863425 Anchorage
TAD1030G; TD1010G; TWD1010G, TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TD100G; TD100G-85; TD100G-87, TD120HP-86; TD121; TD121G
863431
 
863431 Anchorage
TAD1030G; TD1010G; TWD1010G, TD100G; TD100G-85; TD100G-87
863426
 
863426 Anchorage
TAD1030G; TD1010G; TWD1010G, TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TD100G; TD100G-85; TD100G-87, TD120HP-86; TD121; TD121G
863358
 
863358 Anchorage
TAD1030G; TD1010G; TWD1010G, TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TD100G; TD100G-85; TD100G-87, TD120HP-86; TD121; TD121G, TD610G; TWD610G; TD710G, TD61A; TD61AW; TD61ACE
Back to top