3801210 Volvo.Penta Aquamatic drive, exc, SX-A

Table 1
Diagnostic Codes Table
Description Conditions which Generate this Code System Response
827-8 Left Exhaust Temperature Sensor abnormal frequency, pulse width, or period The Electronic Control Module (ECM) detects a sensor frequency that is greater than 1000 Hz or less than 150 Hz.
The ECM detects a duty cycle that is greater than 90 percent or a duty cycle that is less than 10 percent. The value of the parameter is set to zero.
The code is logged.
828-8 Right Exhaust Temperature Sensor abnormal frequency, pulse width, or period The ECM detects a sensor frequency that is greater than 1000 Hz or less than 150 Hz.
The ECM detects a duty cycle that is greater than 90 percent or a duty cycle that is less than 10 percent. System OperationUse this procedure to troubleshoot any suspect problems with the following sensors:
Left exhaust temperature sensor
Right exhaust temperature sensorThe PWM sensors provide a signal to the engine's ECM for certain engine operating conditions. The sensors receive a 8.0 0.4 VDC regulated voltage from the ECM.The sensor's wires are routed from the ECM to the sensor connectors. The following list gives the terminal locations for the sensor connector.
Terminal A 8 V supply
Terminal B sensor return
Terminal C sensor signalThe ECM performs an automatic calibration of these sensors whenever the ECM is powered and the engine has been off for at least five seconds.The ECM provides short circuit protection for the internal power supply. A short circuit to the battery will not damage the internal power supply.
Illustration 1 g01242175
Typical schematic
Illustration 2 g01242178
P1 ECM connector
(P1-4) 8 V supply
(P1-5) Digital return
(P1-11) Left exhaust temperature
(P1-12) Right exhaust temperature
Illustration 3 g01242179
P2 ECM connector
(P2-56) 8 V supply
(P2-66) Digital return
Illustration 4 g01234146
Location of ECM connectors
Illustration 5 g01243506
Sensor connector
(Pin A) Sensor supply
(Pin B) Sensor return
(Pin C) Signal
Illustration 6 g01242181
Rear view
(1) Left exhaust temperature sensor
(2) Right exhaust temperature sensor Test Step 1. Check for an "Active" Diagnostic Code
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Monitor the diagnostic codes on Cat ET. Check and record any diagnostic codes. Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Determine if a diagnostic code has occurred several times. Note: A diagnostic code that is logged several times is an indication of an intermittent problem. Most intermittent problems are the result of a bad connection between a socket and a pin in a connector or a bad connection between a wire and a terminal.
Determine if a -8 diagnostic code is active for one of the exhaust temperature sensors: Expected Result:No diagnostic code is active for the exhaust temperature sensors.Results:
OK - No diagnostic codes are active.Repair: If the problem is intermittent, refer to Troubleshooting, "Inspecting Electrical Connectors" for the correct procedures for inspecting electrical connectors.STOP
Not OK - A -8 diagnostic code is active or the diagnostic code is logged several times. Proceed to Test Step 2.Test Step 2. Check the Digital Supply Voltage at the Sensor Connector
Disconnect the suspect sensor(s) at the sensor connector:
Measure the voltage on the ECM side of the sensor connector between pin A and pin B for the suspect sensor(s). Expected Result:The supply voltage is 8.0 0.4 VDC.Results:
OK - The supply voltage is 8.0 0.4 VDC. Proceed to Test Step 4.
Not OK - The supply voltage is not 8.0 0.4 VDC. Proceed to Test Step 3.Test Step 3. Check the Digital Supply Voltage at the ECM
Remove electrical power from the ECM.
Remove the supply wire from P1-4 or from P2-56. Install a wire jumper into the socket for the supply wire.
Restore electrical power to the ECM.
Measure the voltage between the wire jumper and engine ground.
Remove electrical power from the ECM.
Remove the wire jumper. Expected Result:The supply voltage is 8.0 0.4 VDC.Results:
OK - The supply voltage is 8.0 0.4 VDC. The supply voltage at the ECM is correct. There is a problem in the wiring between the ECM and the sensor connector.Repair: Repair the connectors or wiring and/or replace the connectors or wiring.STOP
Not OK - The supply voltage is not 8.0 0.4 VDC. The voltage at the ECM is not correct.Repair: Replace the ECM. Refer to Troubleshooting, "Replacing the ECM". Verify that the problem is resolved.STOPTest Step 4. Check the Sensor's Duty Cycle at the Sensor Connector
Remove electrical power from the ECM.
Remove the suspect sensor's signal wire from pin C of the sensor connector.
Reconnect the suspect sensor connector.
Restore electrical power to the ECM.
Measure the duty cycle between the sensor's signal wire and pin B of the sensor connector. Note: Set the multimeter to "VDC". Press the "Hz" button twice so that the % symbol is displayed.
Remove electrical power from the ECM.
Replace the sensor's signal wire and reconnect the sensor. Expected Result:The duty cycle is between 10 to 90 percent.Results:
OK - The duty cycle is correct. Proceed to Test Step 5.
Not OK - The duty cycle is incorrect.Repair: Replace the sensor. Verify that no diagnostic codes are active for the suspect sensor before permanently installing the sensor.STOPTest Step 5. Check the Sensor's Duty Cycle at the ECM