848588 Volvo.Penta Baffle plate


848588 Baffle plate Volvo.Penta TD610M; TD630ME; TWD630ME, TD61A; TD61AW; TD61ACE, TD71A; TID71A; TWD710V Baffle
848588 Baffle plate Volvo Penta
Rating:
13

Buy Baffle plate 848588 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$308.60
 

04-09-2017

Boating Ac: Boating Accessories
New Mercury Mercruiser Quicksilver Oem Part # 848588 1 Flame Arrestor
Number on catalog scheme: 25
 

Volvo Penta entire parts catalog list:

TD610M; TD630ME; TWD630ME; TD730ME; TWD730ME; TWD731ME
TD61A; TD61AW; TD61ACE; TD61AG; TD61AGP; TD61AP; TD61APB; TID61AG; TD71A; TD71AW; TD71ACE; TD71AG; TD71AGP; TD71AP; TD71APB; TID71A; TID71AG; TID
TD71A; TID71A; TWD710V; TD730VE; TWD731VE; TAD730V; TWD740VE

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 194-3536 T40 Torx Socket 1
B 227-4389 E10 Torx Socket 1 Note: The crankshaft rear seal and the housing are manufactured as one assembly.Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Failure to follow this procedure could lead to the crankshaft rear seal being damaged.
Illustration 1 g06166503
Illustration 2 g01986154
Ensure that crankshaft flange (1) is clean, dry, and free from damage.
Ensure that the gasket surface of the cylinder block is clean, free from damage, and dry. Ensure that the gasket surface of isolating frame (6) is clean and dry.
Ensure that plastic sleeve (3) is squarely installed within new crankshaft rear seal (2).Note: The plastic sleeve is included to protect the lip of the seal as the crankshaft rear seal is pushed over crankshaft flange (1). Do not attempt to install a crankshaft rear seal without the plastic sleeve.
Place the assembly of crankshaft rear seal (2) over crankshaft flange (1). Align dowel (5) with the slot in crankshaft rear seal (2).
Ensure that plastic sleeve (3) is engaged on crankshaft flange (1). Push crankshaft rear seal (2) squarely onto the crankshaft. Ensure that the crankshaft rear seal is seated against the cylinder block. During this process, plastic sleeve (3) will be forced out of the crankshaft rear seal. Discard the plastic sleeve.Note: Ensure that dowel (5) is engaged in the slot in the crankshaft rear seal.
Illustration 3 g03417136
Tightening sequence for the crankshaft rear seal
Illustration 4 g06166514
Use Tooling (A) to install two outer Torx bolts (7) at the base of crankshaft rear seal (2).
Apply pressure crankshaft rear seal (2) to seat the crankshaft rear seal onto the cylinder block. Tighten Torx bolts (7) to a torque of 15 N m (133 lb in).Note: Applying pressure crankshaft rear seal (2) to seat the crankshaft rear seal onto the cylinder block and onto the isolator plate will ensure that the crankshaft rear seal is not damaged as the bolts are tightened.
Use Tooling (B) to install two Torx bolts (4) to crankshaft rear seal (2) at Position (X).
Apply pressure crankshaft rear seal (2) to seat the crankshaft rear seal onto the cylinder block. Tighten Torx bolts (4) to a torque of 22 N m (195 lb in).
Use Tooling (A) to unscrew Torx bolts (7) by one complete turn.Note: Unscrewing Torx bolts (7) by one complete turn will prevent damage to the crankshaft rear seal (2).
Tighten all remaining Torx bolts (4) in the numerical sequence that is shown in Illustration 3. Tighten all Torx bolts (4) to a torque of 22 N m (195 lb in).
Use Tooling (A) to install remaining Torx bolts (7). Tighten all the Torx bolts to a torque of 22 N m (195 lb in).End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install" for the correct procedure.Installation Procedure Without Isolating Frame for the Oil Pan
Table 2
Required Tools
Tool Part Number Part Description Qty
A 194-3536 T40 Torx Socket 1
C - Alignment Tool 1
- Bolts (M8 by 20 mm) 4 Note: The crankshaft rear seal and the housing are manufactured as one assembly.Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Failure to follow this procedure could lead to the crankshaft rear seal being damaged.


Parts baffle Volvo Penta:

848076
 
848076 Baffle plate
TAMD63L-A; TAMD63P-A, TD610M; TD630ME; TWD630ME, TD610V; TWD610V; TD630VE, TD61A; TD61AW; TD61ACE, TD71A; TID71A; TWD710V
3826485
 
3826485 Baffle plate
TAMD71B; TAMD73P-A; TAMD73WJ-A, TAMD74A; TAMD74A-A; TAMD74A-B, TD71A; TID71A; TWD710V
866268
 
866268 Baffle
TD610G; TWD610G; TD710G, TD71A; TID71A; TWD710V, TWD610P; TWD610PB; TWD710P
4772097
 
4772097 Baffle plate
TD610M; TD630ME; TWD630ME, TD610V; TWD610V; TD630VE, TD61A; TD61AW; TD61ACE
471593
Baffle plate
471593 Baffle plate
TD61A; TD61AW; TD61ACE
4772181
 
4772181 Baffle plate
TD61A; TD61AW; TD61ACE
Back to top