21735450 Volvo.Penta Bearing housing


21735450 Bearing housing Volvo.Penta TAD540-42VE; TAD550-51VE; TAD540VE, TAD570VE; TAD571VE; TAD572VE, TAD840VE; TAD841VE; TAD842VE, TAD870VE; TAD871VE; TAD872VE Bearing
21735450 Bearing housing Volvo Penta
Rating:
83

Buy Bearing housing 21735450 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Volvo Penta entire parts catalog list:

TAD540-42VE; TAD550-51VE; TAD540VE; TAD541VE; TAD542VE; TAD550VE; TAD551VE; TAD552VE
TAD570VE; TAD571VE; TAD572VE
TAD840VE; TAD841VE; TAD842VE; TAD843VE; TAD852VE; TAD851VE; TAD853VE; TAD850-52VE; TAD840-43VE
TAD870VE; TAD871VE; TAD872VE; TAD873VE

Information:

1. Remove shaft (2). Remove pin (1) from the shaft.2. Remove pins (3) from the flyweights. Remove flyweights (4). 3. Remove ring (7), races (8) and bearing (6) from riser (follower) (5).
Cover (7) holds spring (10) under compression.
4. Remove cover (9) and spring (10) from the governor housing.5. Remove lip type seal (11) from cover (9).6. Remove cover (12) for the low and high idle adjustments. 7. Remove locknut and screw (15) for the high idle adjustment.8. Remove bolt (17) and the washer for the low idle adjustment.9. Remove spring (18) and the guide.10. Remove pin (16) and plate (13).11. Remove shaft (14) from the housing. 12. Remove two spacers (19) and pin (20) from the shaft. 13. Remove shaft (21) from the governor housing.14. Remove washer (22) and levers (23) and (24) from the governor housing. 15. Remove lip type seal (25) and the bearing from the governor housing.16. Remove lip type seals (26) and (27) from the governor housing.Assemble Governor
1. Install the bearing and lip type seal in the governor housing with tooling (A). The lip of the seal must be toward the bearing.2. Install lip type seal (1) in the governor housing with tooling (A). The lip of seal must be toward inside of housing.3. Install lip type seal (2) in the governor housing with tooling (B). The lip of seal must be toward the inside of the governor housing. Put lubricant that is to be sealed on the lip of all the seals. 4. Install shaft (3) in the governor housing. 5. Install plates (4), spacers (8) and pin (7) on shaft (5).6. Install shaft (5) in housing and through washer (9) and levers (6). 7. Install pin (11) in holes of the plates.8. Install screw (10) and locknut for high idle adjustment.9. Install spring (13) and the guide.10. Install bolts (12) and washer for the low idle adjustment.
After the fuel injection pump housing and governor have been installed on the engine, make an adjustment for the high and low idle. See GOVERNOR ADJUSTMENT as shown in TESTING AND ADJUSTING.
11. Push the plate and pin (11) over toward bolt (12) and tighten the bolt.12. Install the lip type seal in the cover with tooling (B). The lip of the seal must be toward the inside of the governor housing and installed to a depth of 1.50 1.50 mm (.059 .059 in.) from the outside surface. Put lubricant that is to be sealed on the lip of the seal. 13. Install cover (16) for the idle adjustment screws.
Spring (15) must be installed with the end of the spring as shown in illustration A10291X3.
14. Install spring (15) in the cover. Install cover (14) on the governor housing. 15. Install bearing (19) between races (18) on riser (follower) (17). Install ring (20) that holds the washers on the riser (follower). 16. Install pin in shaft (23).17. Install flyweights (22) and pin (21).18. Install shaft (23) in the flyweight assembly.end by:a) connection of governor to fuel injection pump housing


Parts bearing Volvo Penta:

21534347
 
21534347 Bearing shell
D8A1-A MP; D8A2-A MP, TAD540-42VE; TAD550-51VE; TAD540VE, TAD570VE; TAD571VE; TAD572VE, TAD840VE; TAD841VE; TAD842VE, TAD870VE; TAD871VE; TAD872VE
21796360
 
21796360 Bearing cap
TAD540-42VE; TAD550-51VE; TAD540VE, TAD570VE; TAD571VE; TAD572VE, TAD840VE; TAD841VE; TAD842VE, TAD870VE; TAD871VE; TAD872VE
21730795
 
21730795 Bearing housing
TAD540-42VE; TAD550-51VE; TAD540VE, TAD570VE; TAD571VE; TAD572VE, TAD840VE; TAD841VE; TAD842VE, TAD870VE; TAD871VE; TAD872VE
21742476
 
21742476 Bearing housing
TAD540-42VE; TAD550-51VE; TAD540VE, TAD570VE; TAD571VE; TAD572VE, TAD840VE; TAD841VE; TAD842VE, TAD870VE; TAD871VE; TAD872VE
Back to top