420147 Bearing shield Volvo.Penta
D42A; D42A PP
Bearing
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$38.40
14-07-2021
9.11[4.05] Pounds
-: -
A&I A-MP-12-08-W (HW-MP) Male NPTF Pipe - Rigid - Straight A&I 10143-8-12 MISCELLANEOUS10143812 Riverside Tractor A&I WH12U-108 42-0147 Farm OYL730-10143812 73010143812
$677.29
02-11-2022
20.0[9.00] Pounds
-: -
American Shifter 420147 Shifter Kit (4L60 16" E Brake Cable Clamp Trim Kit For DAD4C)
Application: 4l60 || Shifter Style: Push Button Only || Shifter Arm Size: 16in Single Bend || Shifter Arm Finish: Chrome || Knob: Standard
Application: 4l60 || Shifter Style: Push Button Only || Shifter Arm Size: 16in Single Bend || Shifter Arm Finish: Chrome || Knob: Standard
Compatible models:
D42A; D42A PP
Volvo.Penta
Volvo Penta entire parts catalog list:
Information:
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02570377
Ensure that turbocharger (15) is clean and free from damage. Inspect the turbocharger for wear. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect" for more information. If the turbocharger is worn, the complete turbocharger must be replaced.
Test wastegate actuator (28) for correct operation. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect" for more information. If the wastegate actuator is damaged or the wastegate actuator does not operate within the specified limits, the complete turbocharger must be replaced.
Illustration 2 g02570158
If necessary, follow Step 3.a through Step 3.i in order to install tube assembly (8) and tube assembly (14).
Ensure that tube assembly (8) and tube assembly (14) are clean and free from restriction. Clean the gasket surface of the cylinder block.
Position a new gasket (27) (not shown) onto tube assembly (14).
Position tube assembly (14) onto cylinder block. Install bolts (26) finger tight.
Install bolt (21) and spacer (22) (not shown) finger tight.
Tighten bolts (26) to a torque of 22 N m (195 lb in). Tighten bolt (21) to a torque of 18 N m (159 lb in).
Position a new sealing washer (24) (not shown) onto banjo bolt (23). Install banjo bolt (23) to tube assembly (8) and install remaining new sealing washer (24) (not shown) onto banjo bolt (23).
Position tube assembly (8) onto cylinder block. Tighten banjo bolt (23) finger tight.
Install clip (25) to tube assembly (8) and tube assembly (14). Note: Ensure that the clip is correctly positioned onto tube assemblies.
Tighten banjo bolt (23) to a torque of 40 N m (30 lb ft). Ensure tube assembly (8) is not strained as banjo bolts (23) is tightened. Note: Ensure that the tube assembly does not come into contact with any other engine component.
Illustration 3 g02568359
Clean the gasket surfaces of the exhaust manifold (20). If necessary, install studs (17) (not shown) to the turbocharger (15). Tighten the studs to a torque of 18 N m (13 lb ft).
Position a new gasket (16) (not shown) onto tube assembly (14).
Position a new gasket (16) (not shown) onto exhaust manifold (20).
Position turbocharger (15) on exhaust manifold (20). Note: Do not use the actuator rod to lift the turbocharger.
Install nuts (18). Tighten the nuts to a torque of 44 N m (32 lb ft).
Illustration 4 g02568360
Illustration 5 g02572637
Install bolts (13) to tube assembly (14).
Tighten bolts (13) to a torque of 9 N m (80 lb in).
Lubricate the bearings of turbocharger (15) with clean engine oil through oil inlet port (29). Rotate the shaft of the turbocharger in order to distribute the lubricant.
Position a new sealing washer (4) (not shown) onto banjo bolt (5). Install banjo bolt (5) onto tube assembly (8) and install remaining new sealing washer (4) (not shown) to banjo bolt (5).
Tighten banjo bolt (5) to a torque of 15 N m (133 lb in).
Install clip (9) from tube assembly (8) and tube assembly (14).
Position tube assembly (10) onto turbocharger. Install bolt (3) and bolt (11) finger tight.
Connect hose assembly (2) to the wastegate actuator. Slide hose clamp (12) along the hose assembly. Note: Ensure that hose clamp is correctly position onto the hose assembly.
Install the hose assembly to tube assembly (10). Slide hose clamp (12) along the hose assembly. Note: Ensure that hose clamp is correctly position onto the hose assembly.
Tighten bolt (3) and bolt (11) to a torque of 22 N m (195 lb in).
Connect the hose assemblies to turbocharger inlet (7) and to turbocharger outlet (6) (not shown). Tighten hose clamps securely End By:
Install the exhaust elbow from the turbocharger. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install" for the correct procedure.
Parts bearing Volvo Penta:
240449
240449 Bearing shield
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TA
240455
240455 Bearing bushing
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, DH10A; DH10A 285; DH10A 360, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B;
815329
815329 Bearing
AQD70D; TAMD70D; TAMD70E, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TAMD61A; TAMD62A, TA
815325
815325 Bearing
AQD70D; TAMD70D; TAMD70E, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TAMD61A; TAMD62A, TA
815338
815338 Bearing
AQD70D; TAMD70D; TAMD70E, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TAMD61A; TAMD62A, TA
240530
240530 Bearing shield
D42A; D42A PP, D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B
240531
240531 Bearing bushing
D42A; D42A PP, D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B
233948
233948 Bearing bushing
D42A; D42A PP, D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B