852967 Volvo.Penta Bearing sleeve


852967 Bearing sleeve Volvo.Penta 2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A Bearing

Buy Bearing sleeve 852967 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$139.73
 

02-03-2024
4.61[2.07] Pounds
US: Auto Parts Direct To
APDTY 852967 Power Window Regulator and Motor Assembly Replaces 4798379AB, 56005165
APDTY Meets Or Exceeds OEM Specs || Factory OEM Fit Form And Function
Number on catalog scheme: 98
 

Compatible models:

Volvo Penta entire parts catalog list:

2001; 2001B; 2001AG; 2001BG; 2002; 2002B; 2002D; 2002AG; 2002BG; 2003; 2003B; 2003D; 2003AG; 2003BG; 2003T; 2003TB; 2003 SOLAS; 2003B SOLAS; 2003T
AD30A; AQAD30A; MD30A; TAMD30A; TMD30A; AD30; AQAD30; MD30; TAMD30; TMD30

Information:

1. Remove engine bottom guards.2. Turn off the fuel supply valve at the fuel tank.3. Disconnect fuel lines (1) from the fuel transfer pump.4. Remove the four bolts that fasten fuel transfer pump (2) to the oil pump and remove the fuel transfer pump. Do not remove the two bolts that hold the fuel transfer pump sections together.5. Check the condition of the O-ring seal on the face of the fuel transfer pump. Install a new seal if necessary. Lubricate the seal and the drive spline with clean engine oil.6. Install the fuel transfer pump in the reverse order of removal.7. Open the fuel supply valve at the fuel tank.Disassemble Fuel Transfer Pump
Start By: a. remove fuel transfer pump 1. Pull drive coupling (2) from the pump shaft.2. Remove O-ring seal (1) from the pump. 3. Remove cap (6), seal washer (5), spring (4) and relief valve poppet (3) from the pump bracket assembly. 4. Remove bolts (7), and remove pump head (8) from plate (9). 5. If necessary, remove check valve (10) from head (8). 6. Remove plate (9) from the pump casing.7. Remove gasket (11) and the O-ring seal from the opposite side of plate (9).8. If necessary, remove the bearings from plate (9). 9. Remove gear assembly (12) and shaft assembly (13) from the pump bracket and casing (14). 10. Remove casing (14) and sleeves (15) from pump bracket (16).11. Remove the O-ring seal from casing (14). 12. Remove outer seal (17) and inner seal (18) from bracket (16).13. If necessary, remove the bearings from bracket (16).Assemble Fuel Transfer Pump
1. Use tool group (A) to install the inner and outer lip-type seals in bracket (1). Make sure the lips of the seals are in the position shown at assembly. Put clean engine oil on the lips of the seals.
Use an arbor press to install bearings (2) in the bracket. The bearings must be installed in one continuous stroke of the press to prevent damage to the bearings.
2. Use tool (B) and an arbor press, and install bearings (2) in bracket (1) in one continuous stroke. Install the bearings until they are 1.5 mm (.06 in.) below the surface of the bracket. The inside diameter of the bearings must be 12.736 mm (.5014 in.) after installation. 3. Install sleeves (4) in bracket (1).4. Install O-ring seal (5) in casing (3), and put casing (3) over sleeves (4) on bracket (1). 5. Install gear assembly (6) and shaft assembly (7) in the bracket and casing.
Use an arbor press to install bearings (8) in the plate. The bearings must be installed in one continuous stroke of the press to prevent damage to the bearings.
6. Use tool (B) and an arbor press, and install bearings (8) in plate (9) in one continuous stroke. Install the bearings until they are 1.5 mm (.06 in.) below the surface of the plate. The inside diameter of the bearings must be 12.736 mm (.5014 in.) after installation. 7. Install O-ring seal (10) in plate (9), and put plate (9) in position on the pump casing. 8. Use tool group (A) to install the check valve in head (11) until it makes contact with the shoulder in its bore. Make sure the spring on the check valve is toward the inside before it is installed.
When head (11) is installed, be sure the drain hole (weep hole) is open.
9. Put gasket (12) and head (11) in position on the plate, and install the two bolts that hold the pump together. 10. Install the relief valve poppet (13), spring (14), and the seal washer and cap (15) in the pump. 11. Install O-ring seal (16) around the pump, and put clean engine oil on it.12. Install drive coupling (17) on the pump shaft.End By: a. install fuel transfer pump


Parts bearing Volvo Penta:

48109
 
48109 Bearing bushing
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, D42A; D42A PP, D70B; D70B PP; D70B K, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, MD40A; TMD40A; TMD40B, TD
6210770
 
6210770 Bearing shield
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, MD40A; TMD40A; TMD40B, TD30A; TD31ACE; TD40A, TD60D; TD60D-83; TD60DPP-83, TD70G; TD70
6644949
 
6644949 Bearing bushing
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, D70B; D70B PP; D70B K, MD21B; AQD21B, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, MD40A; TMD40A; TMD40B, TD
852584
 
852584 Bearing housing
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A
851647
Bearing housing
851647 Bearing housing
2001; 2001B; 2001AG, MD11; MD11C; MD11D, MD5A; MD5B; MD5C, MD6; MD6A; MD6B
1542041
 
1542041 Bearing bracket
AD30A; AQAD30A; MD30A, MD40A; TMD40A; TMD40B, TD30A; TD31ACE; TD40A
852372
 
852372 Bearing cover
AD30A; AQAD30A; MD30A, AQ225D; AQ225E; AQ225F, AQ260A; AQ260B; BB260A, BB231A; BB261A, MD40A; TMD40A; TMD40B
814389
 
814389 Bearing sleeve
230A; 230B; 250A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ225D; AQ225E; AQ225F, AQ23
Back to top