469932 Volvo.Penta Bellows


469932 Bellows Volvo.Penta DH10A; DH10A 285; DH10A 360 Bellows
469932 Bellows Volvo Penta
Rating:
33

Buy Bellows 469932 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$571.23
 

25-05-2023
22.0[9.90] Pounds
-: -
American Shifter 469932 Shifter Kit (16" E Brake Cable Clevis Trim Kit Dipstick For E6F2E 4L80E)
Text Color : Black || Street Signs Color : Yellow || Height : 4.375" (11cm) || Length : 20" (50cm) || Feature : Reflective Coating
Number on catalog scheme: 12
 

Compatible models:

Volvo Penta entire parts catalog list:

DH10A; DH10A 285; DH10A 360; DH10A Rail; THD102KD; THD102KB

Information:

Crankshaft Main Bearings
Clean the crankshaft and inspect the crankshaft for wear or damage. Refer to Specifications, "Crankshaft" for more information.
Ensure that all main bearings, main bearing caps, and thrust washers are clean and free from damage. Replace any components that are worn or damaged.
Illustration 1 g03343008
Illustration 2 g03343002
Install lower main bearing shell (5) to lower main bearing cap (3). Note: The lower bearing is a plain bearing that has oil holes.
Install upper main bearing shell (4) to upper main bearing cap (2). Note: The upper bearing has a groove.
Lubricate upper main bearing (4) and lower main bearing (5) with clean engine oil.
Position the upper half of main bearing cap (2) in position on the crankshaft. Position the lower half of main bearing cap (3) in position on the crankshaft. Ensure the correct location and orientation of the bearing caps. The locating tabs for the upper and the lower bearings should be on the same side of the engine. Ensure that the dowels are in the correct position. Correctly positioning the bowels will ensure that the two halves of the main bearing caps are aligned.
Install bolts (1) and upper main bearing cap (2) to lower main bearing cap (6).
Tighten bolts (1) to a torque of 52 N m (38 lb ft).
Rotate the main bearing cap assembly in order to ensure that there is no binding.
Repeat Step 3 through Step 8 in order to install the remaining main bearing.
Illustration 3 g03343014
Illustration 4 g03343003
For the rear main bearing cap assembly, install lower main bearing shell (11) to lower main bearing cap (8). Note: The lower bearing is a plain bearing that has oil holes.
Install upper main bearing shell (10) to upper main bearing cap (7). Note: The upper bearing has a groove.
Lubricate upper main bearing (10) and lower main bearing (11) with clean engine oil.
Position the upper half of main bearing cap (7) in position on the crankshaft. Position the lower half of main bearing cap (8) in position on the crankshaft. Ensure the correct location and orientation of the bearing caps. The locating tabs for the upper and the lower bearings should be on the same side of the engine. Ensure that the dowels are in the correct position. Correctly positioning the bowels will ensure that the two halves of the main bearing caps are aligned.
Install bolts (6) and upper main bearing cap (7) to lower main bearing cap (8).
Tighten bolts (1) to a torque of 52 N m (38 lb ft).
Rotate the main bearing cap assembly in order to ensure that there is no binding. Crankshaft Bearing (Front)
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver 1
Illustration 5 g03343024
Use Tooling (A) to install crankshaft bearing (15) to the cylinder block. Follow Steps 1.a through 1.c in order to install the crankshaft bearing.
Ensure that oil supply hole (18) is aligned with the oil gallery in the cylinder block.
Ensure that joint (15) is upward.
Ensure that chamfer (17) faces toward the cylinder block. End By:
Install the crankshaft assembly. Refer to Disassembly and Assembly, "Crankshaft - Install" for the correct procedure.


Back to top