6643678 Volvo.Penta Bolt

Grounding Practices
Proper grounding for the machine electrical system and engine electrical systems is necessary for proper machine performance and reliability. Improper grounding will result in uncontrolled electrical circuit paths and unreliable electrical circuit paths.Uncontrolled engine electrical circuit paths can result in damage to main bearings, crankshaft bearing journal surfaces, and aluminum components.To ensure proper functioning of the machine and engine electrical systems, an engine-to-frame ground strap with a direct path to the negative battery post must be used. This may be provided by way of a starting motor ground, a frame to starting motor ground, or a direct frame to engine ground.An engine-to-frame ground strap must be used in order to connect the grounding stud of the engine to the frame of the machine and to the negative battery post.The engine must have a wire ground to the battery.Ground wires or ground straps should be combined at ground studs that are only for ground use. All of the grounds should be tight and free of corrosion.All of the ground paths must be capable of carrying any likely current faults. An AWG #0 or larger wire is recommended for the grounding strap to the cylinder head.The engine alternator should have a battery ground with a wire size that is capable of managing the full charging current of the alternator.The engine has several input components which are electronic. These components require an operating voltage.Unlike many electronic systems of the past, this engine is tolerant to common external sources of electrical noise. Buzzers that use electrical energy can cause disruptions in the power supply. If buzzers are used anywhere on the machine, the engine electronics should be powered directly from the battery system through a dedicated relay. The engine electronics should not be powered through a common power source with other activities that are related to the keyswitch.Engine Electrical System
The electrical system has the following separate circuits:
Charging
Starting
Accessories with low amperageSome of the electrical system components are used in more than one circuit. The following components are common in more than one circuit:
Battery or batteries
Circuit breakers
Battery cables
AmmeterThe charging circuit is in operation when the engine is running. An alternator makes electricity for the charging circuit. A voltage regulator in the circuit controls the electrical output in order to keep the battery at full charge.The starting circuit is activated only when the start switch is activated.The accessory circuit with the low amperage and the charging circuit are connected through the ammeter. The starting circuit is not connected through the ammeter.Charging System Components
Alternator
Illustration 1 g01250914
Alternator components
(1) Regulator
(2) Roller bearing
(3) Stator winding
(4) Ball bearing
(5) Rectifier bridge
(6) Field winding
(7) Rotor assembly
(8) Fan The alternator is driven by a belt from the crankshaft pulley. This alternator is a three-phase, self-rectifying charging unit, and the regulator is part of the alternator.The alternator design has no need for slip rings and the only part that has movement is the rotor assembly. All conductors that carry current are stationary. The following conductors are in the circuit:
Field winding
Stator windings
Rectifying diodes
Regulator circuit componentsThe rotor assembly has many magnetic poles that look like fingers with air space between each of the opposite poles. The poles have residual magnetism. The residual magnetism produces a small magnetic field between the poles. As the rotor assembly begins to turn between the field winding and the stator windings, a small amount of alternating current (AC) is produced. The AC current is produced in the stator windings from the small magnetic field. The AC current is changed to direct current (DC) when the AC current passes through the diodes of the rectifier bridge. The current is used for the following applications:
Charging the battery
Supplying the accessory circuit that has the low amperage
Strengthening the magnetic fieldThe first two applications use the majority of the current. As the DC current increases through the field windings, the strength of the magnetic field is increased. As the magnetic field becomes stronger, more AC current is produced in the stator windings. The increased speed of the rotor assembly also increases the current and voltage output of the alternator.The voltage regulator is a solid-state electronic switch. The voltage regulator senses the voltage in the system. The voltage regulator switches ON and OFF many times per second in order to control the field current for the alternator. The alternator uses the field current in order to generate the required voltage output.
Never operate the alternator without the battery in the circuit. Making or breaking an alternator connection with heavy load on the circuit can cause damage to the regulator.
Starting System Components
Starting Solenoid
Illustration 2 g00317613
Starting solenoid
A solenoid is an electromagnetic switch that performs two basic functions:
The starting solenoid closes the high current starting motor circuit with a low current start switch circuit.
The starting solenoid engages the pinion for the starting motor with the ring gear.The solenoid has windings (one set or two sets) around a hollow cylinder or a hollow housing. The solenoid housing has a plunger that is spring loaded. The plunger can move forward and backward. When the start switch is closed and electricity is sent through the windings, a magnetic field is created. The magnetic field pulls the plunger forward in the solenoid housing. This moves the shift lever in order for the pinion drive gear to engage with the ring gear. The front end of the plunger then makes contact across the battery and across the motor terminals of the solenoid. The starting motor then begins to turn the flywheel of the engine.When the start switch is opened, current no longer flows through the windings. The spring now returns the plunger to the original position. At the same time, the spring moves the pinion gear away from the flywheel.When two sets of windings in the solenoid are used, the windings are called the hold-in winding and the pull-in winding. Both of the windings wind around the cylinder for an equal amount of times. The pull-in winding uses a wire with a larger diameter in order to produce a stronger magnetic field. When the start switch is