21311241 Volvo.Penta Bracket

Table 1
J1939 Code and Description CDL Code and Description Comments
626-5
Ether Injection Control Solenoid : Current Below Normal 2417–5
Ether Injection Control Solenoid : Current Below Normal The code is latched.
The code is logged.
Ether injection is disabled.
626-6
Ether Injection Control Solenoid : Current Above Normal 2417–6
Ether Injection Control Solenoid : Current Above Normal The code is latched.
The code is logged.
Ether injection is disabled.
1804-5
Engine Start Enable Device 2 : Current Below Normal 545-5
Ether Start Relay open/short to +batt The code is latched.
The code is logged.
Ether injection is disabled.
1804-6
Engine Start Enable Device 2 : Current Above Normal 545-6
Ether Start Relay short to ground The code is latched.
The code is logged.
Ether injection is disabled.
2632-5
Engine Charge Air Cooler Bypass : Current Below Normal 4698-5
Engine Charge Air Cooler Bypass Valve #1 : Current Below Normal
2632-6
Engine Charge Air Cooler Bypass : Current Above Normal 4698-6
Engine Charge Air Cooler Bypass Valve #1 : Current Above Normal
2634-5
Power Relay : Current Below Normal 3467-5
Main Power Relay : Current Below Normal This code indicates there is a problem with the fuel actuator power supply relay and/or electrical circuit on the ECM
2634-6
Power Relay : Current Above Normal 3467-6
Main Power Relay : Current Above Normal This code indicates there is a problem with the fuel actuator power supply relay and/or electrical circuit on the ECM
2791-5
Engine Exhaust Gas Recirculation (EGR) Valve Control : Current Below Normal 3405-5
EGR Valve Control : Current Below Normal This code indicates that there is an electrical problem with the solenoid valve and/or circuit on the NRS valve actuator.
2791-6
Engine Exhaust Gas Recirculation (EGR) Valve Control : Current Above Normal 3405-6
EGR Valve Control : Current Above Normal This code indicates that there is an electrical problem with the solenoid valve and/or circuit on the NRS valve actuator.
3821-5
Engine Exhaust Gas Recirculation (EGR) Valve 2 Control : Current Below Normal 3406-5
EGR #2 Valve Control : Current Below Normal This code indicates that there is an electrical problem with the solenoid valve and/or circuit on the ERV valve actuator.
3821-6
Engine Exhaust Gas Recirculation (EGR) Valve 2 Control : Current Above Normal 3406-6
EGR #2 Valve Control : Current Above Normal This code indicates that there is an electrical problem with the solenoid valve and/or circuit on the ERV valve actuator.
6721-5
Engine Fuel Injection Pump #2 Fuel Control Valve : Current Below Normal 4774-5
Engine Fuel Injection Pump Control Valve : Current Below Normal
6721-6
Engine Fuel Injection Pump #2 Fuel Control Valve : Current Above Normal 4774-6
Engine Fuel Injection Pump Control Valve : Current Above Normal
7383-5
Engine Throttle Valve 1 Motor Current Disable : Current Below Normal 1440-5
Throttle Actuator : Current Below Normal
7383-6
Engine Throttle Valve 1 Motor Current Disable : Current Above Normal 1440-6
Throttle Actuator : Current Above Normal
7708-5
Engine Turbocharger Compressor Bypass Actuator 1 Motor Current Disable : Current Below Normal 1720-5
Turbocharger Compressor Bypass Valve Actuator : Current Below Normal
7708-6
Engine Turbocharger Compressor Bypass Actuator 1 Motor Current Disable : Current Above Normal 1720-6
Turbocharger Compressor Bypass Valve Actuator : Current Above Normal The applicable Electronic Control Module (ECM) monitors the current flow through the coils of the applicable components.The applicable ECM sets a diagnostic trouble code if the current flow through a coil is incorrect. These codes can be activated only when the applicable ECM is sending a command to the control valves. A -5 code indicates that the current flow through the circuit is low and there is an open in the circuit. A -6 code indicates that the current flow through the circuit is high and there is a short in the circuit.Engine Exhaust Gas Recirculation (EGR) Valve Control refers to the NOx Reduction System (NRS) Valve.Engine Exhaust Gas Recirculation (EGR) Valve 2 Control refers to the Exhaust Restriction Valve (ERV).Electrical Checkouts on the Cat® Electronic Technician (ET)
Table 2
Component Electrical Checkout
Engine Exhaust Gas Recirculation (EGR) Valve EGR Valve Control Override
Engine Exhaust Gas Recirculation (EGR) Valve 2 Control EGR Valve 2 Control Override
Engine Starter Motor Relay Attempt to start the engine. once the ECM attempts to energize the solenoid, the code will become active. Refer to the application-specific schematic for the "Engine Starter Motor Relay wiring circuit."
Engine Positive Crankcase Ventilation System Monitor Engine Crankcase Ventilation Heater Relay Status Override
Ether Solenoid Ether Injection Override
Prelubrication System Relay Prelubrication Relay Override
Illustration 1 g06200301
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -5 code is active or logged.
Proceed to Test Step 2.
Result: A -6 code is active or logged.
Proceed to Test Step 3.
2. Check the Wiring for an Open Circuit
A. Verify that the harness connector is free of debris, free of corrosion, and securely connected.
B. Disconnect the solenoid from the harness.
C. Connect a jumper wire between the terminals of the harness connector for the affected coil. The coil is replaced with a short circuit.
Create a Short
Result: A -5 code became active during the electrical checkout. The ECM did not detect the jumper wire. There is an open circuit in the wiring between the coil and the ECM connector. There may be a problem with a connector.
Repair: Repair or replace the connectors or the wiring.
Verify that the repair eliminated the problem.
Result: A -6 code is activated during the electrical checkout. The ECM detected the jumper wire. There is a problem with the solenoid.
Repair: Replace the solenoid.
Verify that the repair eliminated the problem.
3. Check the Wiring for a Short Circuit
A. Disconnect the solenoid from the harness.
Create an Open
Result: A -6 code became active during the electrical checkout. The ECM did not detect the open circuit. There is a short circuit in the wiring between the coil and the ECM conne