21665358 Volvo.Penta Bracket


21665358 Bracket Volvo.Penta TAD560VE; TAD561VE; TAD761VE Bracket
21665358 Bracket Volvo Penta
Rating:
18

Buy Bracket 21665358 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 15
 

Compatible models:

Volvo Penta entire parts catalog list:

TAD560VE; TAD561VE; TAD761VE; TAD762VE; TAD763VE; TAD764VE; TAD765VE

Information:

START BY:a. remove timing gear cover The automatic timing advance is not used on the 943 loader. 1. Remove bolt (1) and the washer. 2. Install tooling (A), and loosen automatic timing advance (2) on the shaft. Remove tooling (A) and the automatic timing advance.Install Automatic Timing Advance
1. Install the bolt and washer in shaft (1) in the pump drive. Remove the plug from the pump drive housing, and install tool (A) in the plug hole. Turn shaft (1) until timing pin (A) engages in the notch in the shaft. Tool (A) will hold the fuel injection pump camshaft in the correct position to set the fuel injection timing of the engine. 2. Remove the bolt and washer from the shaft, and install automatic timing advance (2) on the shaft. 3. Be sure the threads on bolt (3) and the threads in the shaft of the pump drive are not damaged. Put clean oil on the threads.4. Install bolt (3) and the washer to hold the timing gear on the shaft. Tighten bolt (3) finger tight only. Bolt (3) must be tight enough to hold the gear clearance (backlash) out of the timing gears when the engine is turned. However, the timing gear must be able to turn on the shaft when the engine is turned to put the No. 1 piston on top center compression position (TDC). 5. Put No. 1 piston at the top center compression position (TDC) with the following procedure:a. Remove plug (4) from the flywheel housing. b. Turn the crankshaft clockwise (as seen from the front of the engine) until a 3/8"-16 NC bolt (5) at least two inches long can be installed through the timing hole in the flywheel housing and into the hole in the flywheel. Never turn the crankshaft backward to install the timing bolt in the flywheel. c. Remove breather (6) from the valve cover. Check to see if both rocker arms for the No. 1 piston can be moved backward and forward by hand. The No. 1 piston is at the top center compression position when the bolt is installed in the flywheel, and both rocker arms for No. 1 piston can be moved backward and forward. If both rocker arms cannot be moved, the No. 1 piston is not at the top center compression position. Remove the bolt from the flywheel. Turn the crankshaft clockwise (as seen from the front of the engine) one full turn (360°), and install the bolt again. 6. With the timing pin in the fuel injection pump housing and the timing bolt in the flywheel, tighten the bolt in the timing gear to a torque of 149 7 N m (110 5 lb.ft.).7. Check the timing as follows:a. Remove both the timing pin and timing bolt.b. Turn the crankshaft clockwise (as seen from the front of the engine) two full turns, and install the timing pin and bolt again.c. The timing is correct if both the timing pin and timing bolt can be installed at the same time. The timing procedure must be done again if the timing pin and timing bolt cannot be installed at the same time.d. Remove the timing pin and timing bolt when the timing is correct. 8. Install plug (4) in the flywheel housing. 9. Install breather (6) on the valve cover. 10. Install plug (7) in the fuel injection pump housing.Disassemble Automatic Timing Advance
START BY:a. remove automatic timing advance 1. Remove screws (1) and plate (2) from the hub. 2. Remove springs (3). Do not mix parts of weight assemblies (5).3. Remove limiters (4) and weight assemblies (5) from the hub. 4. Remove gear (6) from hub (7).Assemble Automatic Timing Advance
1. Put gear (1) in position on hub (2) as shown. 2. Put slides (3) in position on weights (4), and install the weights on the hub with the holes in slides (3) over the pins in the hub. Install limiters (5) as shown. 3. Install springs (6) in the openings between the weights and the limiters. 4. Put plate (7) in position, and install the screws that hold it in place.END BY:a. install automatic timing advance


Parts bracket Volvo Penta:

20858519
 
20858519 Bracket
TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE, TAD734GE
20858513
 
20858513 Bracket
TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE, TAD734GE
21280444
 
21280444 Bracket
TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE
21743929
 
21743929 Bracket
TAD560VE; TAD561VE; TAD761VE
21852514
 
21852514 Bracket
TAD560VE; TAD561VE; TAD761VE
22051572
 
22051572 Bracket
TAD560VE; TAD561VE; TAD761VE
21280447
 
21280447 Bracket
TAD560VE; TAD561VE; TAD761VE
20795582
 
20795582 Bracket
TAD560VE; TAD561VE; TAD761VE
Back to top