21665509 Volvo.Penta Bracket


21665509 Bracket Volvo.Penta TAD560VE; TAD561VE; TAD761VE Bracket
21665509 Bracket Volvo Penta
Rating:
48

Buy Bracket 21665509 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Volvo Penta entire parts catalog list:

TAD560VE; TAD561VE; TAD761VE; TAD762VE; TAD763VE; TAD764VE; TAD765VE

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     8S-2241     Camshaft Bearing Tool Group     1    
8H-0684 Ratchet Wrench     1    Start By:
Remove the Flywheel Housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Remove the Oil Pan Plate. Refer to Disassembly and Assembly, "Oil Pan Plate - Remove and Install".
Remove the Camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00478567
Use Tool (A) to remove the camshaft bearing from the cylinder block. Start with the front bearings and work to the rear bearing.Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
A     8S-2241     Camshaft Bearing Tool Group     1    
8H-0684 Ratchet Wrench     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00478567
Use Tool (A) to install the camshaft bearings in the 3304B and 3306B cylinder block.Note: The camshaft bearings in the 3304B have pressure lubrication. The intermediate camshaft bearings and the rear camshaft bearings in the 3306B have splash lubrication.
Install the camshaft bearings in the 3304B cylinder block, as follows: (a) Install the front bearing to a depth of 0.57 0.5 mm (0.022 0.02 inch). Ensure that the oil holes are in a horizontal position and that the camshaft bearing joint is at the top of the engine. The camshaft bearing joint can not be more than 15° degrees from vertical in either direction. (b) Install the center bearing to a depth of 303.2 0.5 mm (11.94 0.02 inch). Ensure that the oil holes in the camshaft bearing are in alignment with the oil holes in the cylinder block. (c) Install the rear bearing to a depth of 604.9 0.5 mm (23.81 0.02 inch). Ensure that the oil holes in the camshaft bearing are in alignment with the oil holes in the cylinder block.
Illustration 3 g00478822
Install the camshaft bearings in the 3306B cylinder block, as follows:
Install front bearing (B) to a depth of 0.5 0.5 mm (.02 .02 inch). Ensure that the oil holes are in a horizontal position and that the camshaft bearing joint is at the top of the engine. The camshaft bearing joint cannot be more than 15 degrees from the vertical position in either direction.
Install the remainder of the bearings. Install the bearings to the dimensions that are given from the front face of the cylinder block: (C) 154.0 0.5 mm (6.06 .02 inch), (D) 303.2 0.5 mm (11.94 .02 inch), (E) 601.7 0.5 mm (23.69 .02 inch) and (F) 903.4 0.5 mm (35.57 .02 inch).End By:
Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
Install the oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".


Parts bracket Volvo Penta:

20858519
 
20858519 Bracket
TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE, TAD734GE
20858513
 
20858513 Bracket
TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE, TAD734GE
21280444
 
21280444 Bracket
TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE
21743929
 
21743929 Bracket
TAD560VE; TAD561VE; TAD761VE
21852514
 
21852514 Bracket
TAD560VE; TAD561VE; TAD761VE
22051572
 
22051572 Bracket
TAD560VE; TAD561VE; TAD761VE
21280447
 
21280447 Bracket
TAD560VE; TAD561VE; TAD761VE
20795582
 
20795582 Bracket
TAD560VE; TAD561VE; TAD761VE
Back to top