21863699 Volvo.Penta Bracket


21863699 Bracket Volvo.Penta TAD550GE; TAD551GE; TAD750GE Bracket
21863699 Bracket Volvo Penta
Rating:
53

Buy Bracket 21863699 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Compatible models:

Volvo Penta entire parts catalog list:

TAD550GE; TAD551GE; TAD750GE; TAD751GE; TAD752GE; TAD753GE; TAD754GE

Information:


3306 Engine Shown1. Put the O-ring seal and water pump (6) in position on the engine, and install bolts (5) to hold them.2. Install the gaskets and water pump elbow (2).3. Tighten clamp (3), and install switch (4) in the water pump elbow.4. On 3306 Engines, slide the hose into position on the water pump elbow, and install clamps (1).5. Install the hose between the radiator and the water pump.6. Fill the radiator with coolant to the correct level. See the Maintenance Guide.Disassemble Water Pump
START BY:a. remove water pump 1. Remove bolt (1) and the washer. Remove bearing (2) and gear (3) as a unit.2. Use tooling (A), (C) and a press, and remove bearing (2) from gear (3). 3. Remove snap ring (4) with tool (B). 4. Remove bolts (5), the washers and cover (6) from the water pump. 5. Loosen bolt (7) 6.4 mm (.25 in.). Hit the bolt with a soft hammer to remove impeller (8) from the shaft.6. Remove the spring and seal assembly from the shaft. 7. Remove bearing (9) and shaft (10) as a unit. 8. Use tooling (A), (C) and a press to remove bearing (9) from shaft (10). 9. Remove the ceramic ring and seal (11) from the housing. 10. Remove lip type seal (12) from the housing with tool (C).Assemble Water Pump
1. Install the lip type seal in the water pump housing with tool (A). The lip of the seal must be toward the bearings. Put clean engine oil on the lip of the seal. 2. Install shaft (1) in bearing (2) with a press. 3. Install shaft (1) and bearing (2) in the housing as shown. 4. Install snap ring (3) with tool (B).
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Put ceramic ring (4) in position in the rubber seal. Use hand pressure and the tool (which is with the replacement ring) to install the ceramic ring. 6. Remove the spring from seal assembly (5). Use hand pressure and the tool (which is with the replacement ring) to install the seal assembly. Push seal assembly (5) on the shaft until it makes light contact with ceramic ring (4). 7. Install spring (6) as shown. Put impeller (7) in position on the shaft, and install the washer and bolt that hold it. Tighten the bolt to a torque of 38 1.4 N m (28 1 lb.ft.). 8. Put the gasket and cover (8) in position on the water pump housing, and install the washers and bolts (9) that hold them. 9. Install bearing (10) on gear (11) with a press. 10. Make an alignment of pins (12) on gear (11) and the holes in shaft (1). Put the gear and bearing in position on the shaft, and install the washer and bolt that hold them together.END BY:a. install water pump


Parts bracket Volvo Penta:

21156350
 
21156350 Bracket, left
D5A-T; D5A-TA; D5A-B TA, TAD550GE; TAD551GE; TAD750GE
20450997
 
20450997 Bracket
TAD520GE; TAD720GE; TAD721GE, TAD520VE; TAD720VE; TAD721VE, TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE, TAD734GE, TAD750VE; TAD760VE, TD420VE; TAD420VE; TAD620VE, TD520GE; TAD530GE; TAD531GE
21004700
 
21004700 Bracket
TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE, TAD734GE
21888902
 
21888902 Bracket
TAD550GE; TAD551GE; TAD750GE
21665202
 
21665202 Bracket
TAD550GE; TAD551GE; TAD750GE
21140359
 
21140359 Bracket
TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE, TAD734GE
21030166
 
21030166 Bracket
TAD550GE; TAD551GE; TAD750GE, TAD734GE
22232497
 
22232497 Bracket
TAD550GE; TAD551GE; TAD750GE
Back to top