22054641 Volvo.Penta Bracket

Illustration 1 g01099622
Schematic
Illustration 2 g01099625
P2 ECM connector
(P2-3) Intake valve actuator pressure solenoid
(P2-79) Solenoid common
Illustration 3 g01104080
Location of components
(1) Intake valve actuator pressure solenoid Test Step 1. Inspect Electrical Connectors and Wiring
Turn the key switch to the OFF position.
Thoroughly inspect the J2/P2 ECM connector and the solenoid connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the solenoid connector.
Check the ECM connector (allen head screw) for the proper torque of 6 N m (55.0 lb in).
Check the harness and wiring for abrasion and for pinch points. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted and the harness and the wiring are free of corrosion, of abrasion, or of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the Cat ET to the service tool connector.
Turn the key switch to the ON position.
Check for active diagnostic codes that are related to the intake valve actuator pressure solenoid.
Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes. Note: Wait at least 15 seconds in order for the diagnostic codes to become active.
Determine if the problem is related to the low current diagnostic code 05 or the high current diagnostic code 06. Expected Result:No diagnostic codes are active.Results:
OK - No diagnostic codes are active.Repair: The problem may have been related to a faulty connection in the harness. Carefully reinspect the connectors and wiring. Refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - A low current diagnostic code (05) is active at this time. Proceed to Test Step 3.
Not OK - A high current diagnostic code (06) is active at this time. Proceed to Test Step 5.Test Step 3. Short the Wires at the Solenoid
Turn the key switch to the OFF position.
Disconnect the intake valve actuator pressure solenoid at the solenoid connector.
Fabricate a jumper wire to short terminal 1 and terminal 2 of the connector for the solenoid on the engine harness.
Turn the key switch to the ON position.
Access the "Special Tests" under the "Diagnostics" menu.
Start the "intake valve actuator pressure solenoid Test" on Cat ET.
Once Cat ET displays the status of the intake valve actuator pressure solenoid, stop the "intake valve actuator pressure solenoid Test". Expected Result:The test indicated "Not Active: Device Short" with the jumper wire in place.Results:
OK - The test indicated "Not Active: Device Short". The ECM recognized the short at the connector for the intake valve actuator pressure solenoid. The harness wiring is OK.Repair: Temporarily connect a new intake valve actuator pressure solenoid to the harness, but do not install the new intake valve actuator pressure solenoid in the engine. Verify that there are no active diagnostic codes for the intake valve actuator pressure solenoid. If there are no active diagnostic codes for the intake valve actuator pressure solenoid, permanently install the new intake valve actuator pressure solenoid. Clear any logged diagnostic codes.STOP
Not OK - The test indicated "Not Active: Device Open". The ECM did not see the short at the connector for the intake valve actuator pressure solenoid. Proceed to Test Step 4.Test Step 4. Create a Short