3588656 Volvo.Penta Bracket

Interfacing With a Shipyard
Provide table 3 to table 6.Provide the following list of information about the configuration:
Modbus is the protocol that the MMS uses for outputting data.
Ports for hardware are available. The ports have 9 pins. The RS-485 has one connection with 2 wires and two connections with 4 wires. The RS-232C has one connection with handshaking and two connections without handshaking.
Provide the list of baud rates.
The network addresses can be a number between 1 and 247.
The system uses a serial cable that has 9 pins. The cable has shielding.Control System Inputs to PLC Redundant Relay Logic
Table 1
PLC I/O Address    Description of Sensor    PLC Alarm Address    Type of Signal    Alarm    Shut Down    Setpoint for Trip    Comments    
Pressure Contactors    
I:1.0/1
(I:1.0/0)     "Engine Low Oil Pressure"
144-0102     B37:10/0     DIGITAL         X     Close Contact     Low Speed    
I:1.0/3
(I:1.0/2)     "Engine Low Oil Pressure"
144-0102     B37:36/0     DIGITAL         X     Close Contact     High Speed    
I:1.0/5
(I:1.0/4)     "Engine High Crankcase Pressure"
117-1864     B37:20/0     DIGITAL         X     Close Contact        
I:2.0/3
(I:2.0/2)     "Generator Oil Pressure Low"     B37:47/0     DIGITAL         X     Close Contact        
I:2.0/5
(I:2.0/4)     "Jacket Water Pressure Low"     B37:26/0     DIGITAL         X     Close Contact        
I:1.0/14     "Seawater Differential Pressure"     B39:87/0     DIGITAL     X         Open Contact        
Switch and Miscellaneous Contacts    
I:2.0/12     "Low Battery Voltage - U.P.S."
7C-3508     B39:118/0     DIGITAL     X         Open Contact     "Alarm picks up at ≤22 VDC"    
I:2.0/11     "Low Battery Voltage - P.M."
7C-3508     B39:126/0     DIGITAL     X         Closed Contact     "Alarm picks up at ≤22 VDC"    
I:2.0/13     "Jacket Water Detection"
125-4340     B39:134/0     DIGITAL     X         Open Contact        
I:3.0/0     "Emergency Stop (Local)"     B37:24/0     DIGITAL         X     Close Contact        
I:1.0/8     "Engine Speed Switch Crank Terminate"
100-5675     B33:0/5     DIGITAL     X         > 170 RPM + 2 Seconds     "Engine is Running Determination"    
I:1.0/9     "Engine Speed Switch Alarm Time Delay"
100-5675     None     DIGITAL     X         9 Seconds After SS-001     Low Speed Condition Pressure Alarms    
I:1.0/10     "Engine Speed Switch Oil Pressure Step"
100-5675     None     DIGITAL     X         75% Rated Speed     High Speed Condition Pressure Alarms    
I:2.0/0     "Engine Oil Level Low"     B39:132/0     DIGITAL     X         Open Contact        
I:1.0/7     "Starting Oil Sensor Auxiliary Relay"
3N-1400         DIGITAL                 Engine Auto Start Interlock    
I:1.0/13     "Generator Stator Oil Pressure"         DIGITAL                 Engine Auto Start Interlock    
I:2.0/11
I:1.0/11     "Engine Overspeed (Engine Speed Switch)"
100-5675     B37:18/0     DIGITAL         X     Close Contact from ESS        
I:3.0/1     "Fuel Control Switch"         DIGITAL                    
I:3.0/5     "Remote Start"         DIGITAL                    
I:3.0/6     "Remote