831247 Volvo.Penta Bracket


831247 Bracket Volvo.Penta AQ115A; AQ115B; AQ130 Bracket
831247 Bracket Volvo Penta
Rating:
103

Buy Bracket 831247 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$225.00
 

05-07-2020

-: -
831247 Electronic Ignition Conversion Ford N Series NAA NAB 2N 8N
Replacement Tractor Part 831247 ELECTRONIC IGNITION KITS for FORD N SERIES NAA NAB 2N 8N and more. || Parts for FORD tractor, refurbished Parts for FORD tractors, tractor cultivator Parts, tractor hubs for sale, Parts FORD tractors, used tractor Parts, combine Parts for sale, Parts tractors, 831247, ELECTRONIC IGNITION KITS || ELECTRONIC IGNITION CONVERSION || FORD N SERIES ELECTRONIC IGNITION KITS, FORD NAA ELECTRONIC IGNITION KITS, FORD NAB ELECTRONIC IGNITION KITS, FORD 2N ELECTRONIC IGNITION KITS, FORD 8N ELECTRONIC IGNITION KITS, FORD 9N ELECTRONIC IGNITION KITS
Number on catalog scheme: 59
 

Compatible models:

Information:

2. Remove the bolts, and remove damper guard (1) from the engine. 3. Remove bolts (4), and remove elbow (3) and tube (2) as a unit from the engine. 4. Remove bolts (5) that hold the water pump to the drive adapter. 5. Fasten a hoist to water pump (7), and remove bolts (6) to remove the water pump from the engine. The weight of water pump (7) is 27 kg (60 lb.).Install Water Pump
1. Make sure gasket (3) is in position on the water line adapter. Install O-ring seal (2) on the pump housing, and put clean engine oil on it.2. Fasten a hoist to water pump (1), and put it in position in the pump drive. Make sure the splines on the pump shaft are correctly engaged with the pump drive splines. 3. Install bolts (4) and (5) that hold the water pump to the water line adapter and the pump drive adapter. 4. Install O-ring seal (8) on the pump housing, and put clean engine oil on it.5. If necessary, make a replacement of the O-ring seals on each end of tube (6), and put clean engine oil on the seals.6. Put tube (6) and elbow (7) as a unit in position, and install the bolts to hold these in position. 7. Install damper guard (9) on the engine.8. Fill the cooling system with coolant to the correct level. See the Maintenance Manual.Disassemble Water Pump
Start By:a. remove water pump 1. Remove elbow (1) from housing assembly (2). Remove the O-ring seal from elbow (1). 2. Remove O-ring seal (5) from the back of housing assembly (2).3. Remove washer (4) that holds shaft assembly (3) in housing assembly (2). 4. Remove cover (6) from housing assembly (2). Remove the O-ring from cover (6). Later model water pumps use a nut to hold the impeller on the shaft instead of bolt (8).5. Loosen bolt (8) and the washer that hold impeller (7) to the pump shaft. Use tooling (A) to loosen impeller (7) from the end of the pump shaft. Remove tooling (A), bolt (8), the washer and impeller (7) from the pump shaft and housing assembly (2). 6. Remove spring (10) from seal assembly (9) and shaft assembly (3).7. Use a soft faced hammer and push shaft assembly (3) out of seal assembly (9) and housing assembly (2). Remove seal assembly (9) from housing assembly (2). 8. Remove ceramic seal (11) from the rubber ring. Remove the rubber ring from housing assembly (2). 9. Remove seal (12) from the back of housing assembly (2).Assemble Water Pump
1. If necessary, make a replacement of the two filters in the pump housing at location (1).2. If necessary, make a replacement of plug (2) and the seal.3. Use tool group (A) to install the seal in the housing assembly. Make sure the lip of the seal is toward the outside as shown. Put clean engine oil on the lip of the seal. 4. Install shaft assembly (3) in housing assembly (4). Install washer (5) and the bolts to hold shaft assembly (3) in position.
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Put ceramic seal (6) in position in the rubber ring. Use hand pressure and the tool (which is with the replacement seal) to install the ceramic seal. 6. Remove the spring from seal assembly (7). Use hand pressure and the tool (which is with the replacement seal) to install the seal assembly. Push the seal assembly on the shaft until the seal faces make light contact. 7. Install spring (8) on the carbon seal assembly.8. Put impeller (9) in position on the pump shaft as shown. 9. Install washer (11) and bolt (10). Tighten bolt (10) to a torque of 90 15 N m (66 11 lb.ft.). Hit the bolt with a hammer, and tighten it again to a torque of 90 15 N m (66 11 lb.ft.). Later model water pumps use a nut on the shaft assembly instead of bolt (10). Tighten the nut to a torque of 200 25 N m (148 18 lb.ft.). 10. Make sure the studs for cover (12) are tightened to a torque of 27 4 N m (20 3 lb.ft.) in the pump housing.11. Put clean engine oil on O-ring seal (13), and install it on cover (12). Put cover (12) in position, and install the nuts to hold it to the pump housing. 12. Put clean engine oil on the O-ring seal, and install it in elbow (14). Put elbow (14) in position on housing assembly (4), and install the bolts to hold the unit together.13. Put clean engine oil on the O-ring seal, and install it on the back of housing assembly (4).End By:a. install water pump


Parts bracket Volvo Penta:

829083
 
829083 Bracket
AQ115A; AQ115B; AQ130, MD21B; AQD21B
831130
 
831130 Bracket
AQ115A; AQ115B; AQ130
831947
 
831947 Bracket
AQ115A; AQ115B; AQ130
818432
 
818432 Bracket
AQ115A; AQ115B; AQ130
831866
 
831866 Bracket
AQ115A; AQ115B; AQ130
806342
Bracket
806342 Bracket
AQ115A; AQ115B; AQ130
430116
Bracket
430116 Bracket
AQ115A; AQ115B; AQ130
826638
 
826638 Bracket
AQ115A; AQ115B; AQ130
Back to top