861485 Volvo.Penta Bracket


861485 Bracket Volvo.Penta AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D Bracket
861485 Bracket Volvo Penta
Rating:
73

Buy Bracket 861485 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Volvo Penta entire parts catalog list:

AD31D; AD31D-A; AD31XD; TAMD31D; TMD31D
AD31L-A; AD31P-A; AD41L-A; AD41P-A; D41L-A; TAMD31L-A; TAMD31M-A; TAMD31P-A; TAMD31S-A; TAMD41H-A; TAMD41H-B; TAMD41P-A; TAMD41L-A; TAMD41M-A
AD41D; D41D; TAMD41D; TMD41D; HS1A

Information:


Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 1 g02173073
If necessary, follow Step 2.a through Step 2.d in order to install bracket (29).
Position bracket (29) onto cylinder head (30).
Install bolts (28) hand tight. Ensure that rubber sleeve (32) is correctly positioned into recess of bracket (29).
Tighten bolts (28) to a torque of 22 N m (195 lb in).
Install new cable straps (31). Note: Ensure that the cable straps meet Original Equipment Manufacturers (OEM) specification.
Illustration 2 g02169940
Illustration 3 g02169941
Position a new gasket (15) onto inlet air control assembly (6). Ensure gasket (15) is correctly installed into locating Pins (A).
Loosen bolts (34) for bracket (33).
Illustration 4 g02169794
Illustration 5 g02351557
Illustration 6 g02169941
Position inlet air control assembly (6) onto bracket. Note: Ensure that the inlet air control assembly is correctly installed onto hose assembly for the inlet elbow.
Install bolts (25) and bolts (14) hand tight.
Tighten bolts (25) to a torque of 22 N m (195 lb in).
Tighten bolts (14) to a torque of 22 N m (195 lb in).
Tighten bolts (34) for bracket (33) to a torque of 44 N m (32 lb ft).
Connect temperature sensor (16) to the inlet air control assembly. Refer to Disassembly and Assembly, "Temperature Sensor (Cooled Exhaust Gas) - Remove and Install" for the correct procedure.
Install a new sealing washer (20) (not shown) to banjo bolt (22). Install banjo bolt (22) to tube assembly (23).
Position tube assembly (23) onto inlet air control assembly (6). Install install remaining new sealing washer (20) (not shown) to banjo bolt (22). Install banjo bolt (22) finger tight.
Install bolt (17) (not shown) and bolt (25) to clips for tube assembly (23).
Tighten banjo bolt (21) to a torque of 15 N m (133 lb in).
Tighten bolt (17) (not shown) and bolt (25) to a torque of 22 N m (195 lb in).
Install hose assembly onto turbocharger wastegate actuator and slide clip (19) along hose assembly. Note: Ensure that clip for hose assembly is correctly positioned onto the hose assembly.
Position a new hose clamp (17) and a new hose clamp (19) onto hose assembly (26) and hose assembly (27).
Install hose assembly (26) and hose assembly (27) to the connections on the inlet air control assembly (6).
Tighten hose clamp (17) and hose clamp (19) securely.
Illustration 7 g02169793
Connect hose assembly (7) to inlet connection (19) for inlet air control (6). Tighten hose clamps (8) to a torque of 6 N m (53 lb in).
Tighten hose clamps (12) for the hose assembly that connects inlet air control assembly (6) to inlet elbow (13). Tighten the hose clamps to a torque of 6 N m (53 lb in).
Slide connection for wiring harness assembly for wastegate solenoid (5) onto bracket (2). Connect the engine wiring harness assembly to wiring harness assembly for wastegate solenoid (5). Slide locking tab in to the locked position.
Slide connection for wiring harness assembly (4) onto bracket (2). Connect engine wiring harness assembly (1) to wiring harness assembly (4) for the NRS valve. Slide locking tab in to the locked position
Connect engine wiring harness assembly (10) to engine inlet throttle valve (11). Slide locking tab in to the locked position.
Install new cable straps to engine wiring harness assemblies. Ensure that all cable straps are installed to the harness assemblies. Note: Ensure that the cable straps meet OEM specification.


Parts bracket Volvo Penta:

843260
Bracket
843260 Bracket
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G, D3-110I-H; D3-140A-H; D3-140I-H, D4-180I-B; D4-180I-C; D4-180I-D, D
838583
 
838583 Bracket
AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, TD30A; TD31ACE; TD40A
853039
 
853039 Bracket
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ131A; AQ131B; AQ131C, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ17
858177
 
858177 Bracket
AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D4-180I-B; D4-180I-C; D4-180I-D, D4-180I-F; D4-225A-F; D4-225I-F, D6-280A-A; D6-280A-B; D6-280A-C, D6-300A-F; D6-300D-F; D6-300I-F, MD31A; TMD31A; TMD31B,
1542211
 
1542211 Bracket
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A, MD31A; TMD31B; TAMD31B, MD40A; TMD40A; TMD40B, TD30A; TD31ACE; TD40A, T
861387
 
861387 Bracket
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A, MD31A; TMD31B; TAMD31B, TMD41B; D41B; TAMD41B
854438
Bracket
854438 Bracket
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, DP-C1; DP-D1; DP-S, DP-E; SP-E; TSK DP-E, DP-G; TSK DP-G, DPX-A; TSK DPX-A, DPX-R; DPX-R 1.47; DPX-
3580719
 
3580719 Bracket
AD31L-A; AD31P-A; AD41L-A, KAD32P; TAMD42WJ-A; KAD43P-A
Back to top