1589430 Volvo.Penta Brake drum


1589430 Brake drum Volvo.Penta RAN181; RAN280; RAN480 Brake
1589430 Brake drum Volvo Penta
Rating:
103

Buy Brake drum 1589430 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 39
 

Compatible models:

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Note: The following oil pressure measurements are taken between the oil filter and the engine lubrication system. Before you begin this procedure, ensure that the area around the oil pressure port is clean and dry. Be careful not to introduce any form of contamination into the lubrication system during this procedure.
Illustration 1 g02286393
Location of the pressure tap for the lubrication system (front side engine view)
(1) Metric plug (M14)
(2) 266-2177 Elbow
Table 1
Tools Needed for Oil Pressure Measurements at the 266-2177 Elbow
Part Number Part Name Quantity
1U-5470 Engine Pressure Group 1
5C-7617 Reducing Bushing 1
4M-5317 Reducing Bushing 1 Certain engines may also be equipped with a 302-5924 Cover at the front of the oil filter group. For these engines, the oil pressure measurement may be taken at the plug in the oil cover. The procedure for the oil pressure measurement at either location is the same.
Illustration 2 g03670644
Location of the pressure tap for the lubrication system (front engine view)
Table 2
Tools Needed for Oil Pressure Measurements at the 302-5924 Cover
Part Number Part Name Quantity
1U-5470 Engine Pressure Group 1
8T-7860 Reducing Bushing 1
5P-5528 Reducing Bushing 1
Illustration 3 g00296486
1U-5470 Engine Pressure Group
The 1U-5470 Engine Pressure Group measures the engine oil pressure in the system. This engine tool group can read the engine oil pressure inside the oil manifold.Note: Refer to Special Instruction, SEHS8907, "Using the 1U-5470 Engine Pressure Group" for more information on using the 1U-5470 Engine Pressure Group.Note: The engine oil pressure can also be measured by using an electronic service tool. Refer to Troubleshooting for information on the use of the Caterpillar Electronic Technician (ET).
Remove the plug from the appropriate location for your engine. Install the appropriate bushings into the fitting for the pressure tap. These bushings will reduce the size of the tap to the correct size for the 1U-5470 Engine Pressure Group. Install the fitting for the pressure group into this port. Note: The fitting for the pressure tap is a metric size. Do not use a SAE or an NPTF fitting in this port.
Start the engine. Run the engine with SAE 15W40 oil. Refer to Operation and Maintenance Manual, "Engine Oil" for the recommendations of engine oil. Note: Allow the engine to reach operating temperature before you perform the oil pressure test.Note: The nominal engine oil temperature at rated rpm is approximately 95° C (203° F). The engine oil temperature must not exceed 115 °C (239 °F).
Record the value of the engine oil pressure when the engine has reached operating temperature.
The normal engine oil pressure at rated rpm is approximately 500 kPa (73 psi) to approximately 700 kPa (102 psi). The maximum engine oil pressure must never exceed 850 kPa (123 psi). The minimum engine oil pressure at rated rpm must never drop below 500 kPa (73 psi). The specification for the minimum engine oil pressure at low idle rpm is 280 kPa (40 psi). Note: A record of engine oil pressure can be used as an indication of possible engine problems or of damage. A possible problem could exist if the engine oil pressure suddenly increases or decreases 70 kPa (10 psi) and the engine is not at normal engine oil pressure. Inspect the engine and correct the problem.
Compare the recorded engine oil pressure with the engine oil pressure indicators on the instrument panel and the engine oil pressure that is displayed on Cat ET.
A faulty oil pressure indicator or a faulty oil pressure sensor can give a false indication of engine oil pressure. If there is a notable difference between the engine oil pressure readings, refer to the Troubleshooting manual for troubleshooting details.


Parts brake Volvo Penta:

353541
Brake cam
353541 Brake cam
D120A; D120AK; TD120A, RAN181; RAN280; RAN480, TD120C
353540
Brake cam
353540 Brake cam
D120A; D120AK; TD120A, RAN181; RAN280; RAN480, TD120C
1575527
 
1575527 Brake cam
D120A; D120AK; TD120A, RAN181; RAN280; RAN480, TD120C
276047
 
276047 Brake lining kit
RAN181; RAN280; RAN480
353538
Brake cam, 435MM-1/2UNC
353538 Brake cam, 435MM-1/2UNC
RAN181; RAN280; RAN480
1607827
 
1607827 Brake lever
RAN181; RAN280; RAN480
3091459
 
3091459 Brake lining kit
RAN181; RAN280; RAN480
854255
Brake lining kit
854255 Brake lining kit
RAN181; RAN280; RAN480
Back to top