3964604 Bushing Volvo.Penta
D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, TAD1240GE; TAD1241GE; TAD1242GE, TWD1240VE; TAD1241VE; TAD1242VE
Bushing
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$118.36
08-09-2020
-: -
Genuine Cummins 3964604 TUBE,INJECTOR FUEL SUPPLY
Factory Direct Shipped Genuine Cummins Part || Availability can vary, please contact for availability before ordering || May take up to 20 business days to ship. Shipping depends upon availability
Factory Direct Shipped Genuine Cummins Part || Availability can vary, please contact for availability before ordering || May take up to 20 business days to ship. Shipping depends upon availability
$167.92
30-09-2018
Hastings: Hastings
Automotive Oil Filter - Case 8900126397, Caterpillar 3964604, Donaldson ELF7300, Fleetguard LF9009, Fram HPH9500, John Deere PMLF9009
Filter Type: Oil Filter||Fram Part Number: HPH9500||Purolator Part Number: L56019||Donaldson Part Number: ELF7300||Fleetguard Part Number: LF9009
Filter Type: Oil Filter||Fram Part Number: HPH9500||Purolator Part Number: L56019||Donaldson Part Number: ELF7300||Fleetguard Part Number: LF9009
Compatible models:
Volvo Penta entire parts catalog list:
- Cylinder Head » 3964604
TAD1240GE; TAD1241GE; TAD1242GE
TWD1240VE; TAD1241VE; TAD1242VE; TAD1250VE; TAD1251VE; TAD1252VE
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Cap Kit 1
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g02210473
Clean the area around flow control valve (3) and fuel injection pump. Ensure that the area is free from contamination before beginning disassembly.
Disconnect harness assembly (1) from flow control valve (3).
Disconnect plastic tube assembly (4). Use Tooling (A) in order to plug and cap the open port on the fuel injection pump and the plastic tube assembly with new plug and new cap.
Make temporary marks on flow control valve (3) and the fuel injection pump for installation purpose.
Remove allen heads screws (2) from flow control valve (3).
Remove flow control valve (3) from the fuel injection pump.
Remove O-ring seal (5) from fuel injection pump. Installation Procedure
Ensure that all component at free from wear and damage. If any part of the flow control valve is worn or damaged, the flow control valve must be replaced as an assembly. The flow control valve kit contains the guide pins in order to install the flow control valve assembly.
Illustration 2 g02208673
Illustration 3 g02306933
Flow control valve guide pins
Position a new O-ring seal (5) onto the flow control valve assembly.
Check O-ring seal (6) is correctly positioned. Ensure that O-ring seal (6) is not damaged. Note: If O-ring seal (6) is damaged, a new flow control valve assembly must be installed.
Install guide pins into Position (X) on the fuel injection pump. Note: Note the guide pins are part of the flow control valve repair kit.
Lubricate O-ring seal (6) with clean fuel. Note: Ensure that the O-ring seal is not damaged or misaligned.
Align flow control valve (3) onto guide pins.
Install flow control valve (3) to the fuel injection pump.
Remove guide pins from the fuel injection pump.
Install allen head screws (2) from the flow control valve repair kit.
Tighten allen head screws (2) equally until the flow control valve is seated correctly onto the fuel injection pump. Note: Ensure that the allen screws are tightened equally. Failure to ensure that the allen screws are tightened equally will result in damage to the fuel injection pump.
Tighten the allen head screws to a torque of 9 N m (80 lb in).
Connect harness assembly (1) to flow control valve (3).
Remove plug and cap from ports from the fuel injection pump and the plastic tube assembly.
Connect plastic tube assembly (4).
Replace the filters for primary fuel system. Refer to Operation and Maintenance Manual, "Fuel System Primary (Water Separator) Element - Replace" for the correct procedure.
Replace the filters for secondary fuel system. Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for the correct procedure.
Turn the fuel supply to the ON position.
Turn the battery disconnect switch to the ON position.
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for more information. End By:
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.
After replacement of the flow control valve, the fuel injection pump requires a high-pressure fuel pump calibration procedure to be performed. Refer to Troubleshooting, "Fuel Rail Pressure Problem" for the correct procedure.
Parts bushing Volvo Penta:
3829680
3829680 Bushing
D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D11B3-A MP; D11B4-A MP, D12D-A MH; D12D-B MH; D12D-C MH, D13B-E MH; D13B-E MH (FE); D13B-N MH, D16C-A MH; D16C-B MH; D16C-C MH, D16C-D MH, D3-110I-A; D3-110I-B; D3-110I-C, D4-180I-B; D4-180I-C; D4-180I-
20381185
20381185 Bushing
D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, TAD1240GE; TAD1241GE; TAD1242GE, TAMD122A; TMD122A; TAMD122P-A, TD121G-87; TWD1210V; TWD1211V, TWD1240VE; TAD1241VE; TAD1242VE
3827694